TU manifold .63 TN for dbb and "shadow" 3 inch s-w

[Dr. Johny Dodge]

Date: 31st March 2023
Username: Dr. Johny Dodge


SOLD SOLD and SOLD..thanks much !!

manifold started to flash rust in damp basement so it got a hit of "oxford white fi50 colour match.. paint is not an exhaust paint and should be removed if you care about that kind of thing

drilled for chrysler flange and comes as cast , no porting

TU hardware bits included in original bag

turbine housing is a turbonetics .63 housing cut out to fit duel ball bearing garret turbo

the inside of the snail shell has been "smoothened"

the 2 half cressant pieces that look like parts of a piston ring are spacers to go between the turbine housing and center section

swing valve is one of those "Shadow" was making a few years back and fits nicely with the TU manifold, moving down pipe back somewhat towards the original placement in the car

the dounut seal and bolts he included with it are included

I have 1400 cdn invested .. so that's the starting price..plus postage and pay pal fees

I would prefer to sell as a package deal rather than sepperate pieces

[Dr. Johny Dodge]

the

[Dr. Johny Dodge]

swing valve casting requires some minor grinding to ease back the bolt bosses cast in housing where it mounts to turbine housing ..re top pic above

[4 l-bodies]

Johny, might be helpful to know what turbine shaft the housing has been cut for. For example JUST the GT3071R had turbine options of a 60/55 and a 56.5/51.8 or even a 56.5 53.6mm. Put me at the top of the list if you want to sell the swingvalve, should you decide to piece it out.
Todd

[4 l-bodies]

swing valve casting requires some minor grinding to ease back the bolt bosses cast in housing where it mounts to turbine housing ..re top pic above

Yes Johny, I had to deal with that too on the one I bought many years ago. This is how much I had to remove for stage II or III turbine housing cut.

[Dr. Johny Dodge]

x x x

[evil89spirit]

Do you still have the manifold and swing valve, if so please send me a PM as I am very interested.

[turbovanpilot]

Interested in the tu header only, if you want to sell separately

[Dr. Johny Dodge]

ok, FINALLY got myself back online

sorry all for "dropping out" .. been dealing with the issue of being broke ,no internet, having a phone that's so stuffed with updates it "bricks up in hours after reset .. and an executor/trustee for my parents estates that I haven't heard a word out of for almost two years..

and, pay pal..I think I have that working properly , again

been a sxxx show of a summer here ..

I still have the above parts .. and will follow up with those who expressed interest in the order they did so..

there are a couple of PM's in my box I need to catch up on ..


and first, turbine housing appears to be machined out to a cavity / bore size of 57mm

measured with a good metal ruler , sweeping it across the opening from two diagonal measurements at 55mm it shows a "sweep that goes 57mm, inside edge to inside edge when the point of "straight across the hole" is found

my caliper has gone..missing

small piece of advice.. never choose a family member as executor or trustee for your estate.. this you and your beneficiaries will benefit from ..IF you hire a lawyer to assume the responsibilities

[Dr. Johny Dodge]

am separating parts.. shadow swing valve is pending, manifold and turbine housing are still available

turbine housing measures at 57 mm opening

manifold comes with TU parts kit

turbine housing comes with required spacer rings for center section mounting and
the snail shell has been smoothened internally

asking TU price of $475 us for manifold + shipping and p-p fee

$175 + shipping & p-p fee for turbine housing

[Dr. Johny Dodge]

swing valve is sold

[Dohcturbo]

Hi,

Is TU Header still available?

am separating parts.. shadow swing valve is pending, manifold and turbine housing are still available

turbine housing measures at 57 mm opening

manifold comes with TU parts kit

turbine housing comes with required spacer rings for center section mounting and
the snail shell has been smoothened internally

asking TU price of $475 us for manifold + shipping and p-p fee

$175 + shipping & p-p fee for turbine housing

[Dr. Johny Dodge]

sorry all three pieces are sold