Results 1 to 13 of 13

Thread: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

  1. #1
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    SOLD ..TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    Date: 31st March 2023
    Username: Dr. Johny Dodge


    SOLD SOLD and SOLD..thanks much !!

    manifold started to flash rust in damp basement so it got a hit of "oxford white fi50 colour match.. paint is not an exhaust paint and should be removed if you care about that kind of thing

    drilled for chrysler flange and comes as cast , no porting

    TU hardware bits included in original bag

    turbine housing is a turbonetics .63 housing cut out to fit duel ball bearing garret turbo

    the inside of the snail shell has been "smoothened"

    the 2 half cressant pieces that look like parts of a piston ring are spacers to go between the turbine housing and center section

    swing valve is one of those "Shadow" was making a few years back and fits nicely with the TU manifold, moving down pipe back somewhat towards the original placement in the car

    the dounut seal and bolts he included with it are included

    I have 1400 cdn invested .. so that's the starting price..plus postage and pay pal fees

    I would prefer to sell as a package deal rather than sepperate pieces
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	004 (2).jpg 
Views:	103 
Size:	820.8 KB 
ID:	66232   Click image for larger version. 

Name:	006 (2).jpg 
Views:	79 
Size:	780.7 KB 
ID:	66233   Click image for larger version. 

Name:	005 (2).jpg 
Views:	80 
Size:	823.4 KB 
ID:	66234   Click image for larger version. 

Name:	007 (2).jpg 
Views:	78 
Size:	998.5 KB 
ID:	66235  
    Last edited by Dr. Johny Dodge; 09-16-2023 at 08:35 PM.

  2. #2
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    the

  3. #3
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    swing valve casting requires some minor grinding to ease back the bolt bosses cast in housing where it mounts to turbine housing ..re top pic above

  4. #4
    turbo addict
    Join Date
    Dec 2006
    Location
    MPLS, MN
    Posts
    3,601

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    Johny, might be helpful to know what turbine shaft the housing has been cut for. For example JUST the GT3071R had turbine options of a 60/55 and a 56.5/51.8 or even a 56.5 53.6mm. Put me at the top of the list if you want to sell the swingvalve, should you decide to piece it out.
    Todd
    Last edited by 4 l-bodies; 04-02-2023 at 05:19 PM.

  5. #5
    turbo addict
    Join Date
    Dec 2006
    Location
    MPLS, MN
    Posts
    3,601

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    Quote Originally Posted by Dr. Johny Dodge View Post
    swing valve casting requires some minor grinding to ease back the bolt bosses cast in housing where it mounts to turbine housing ..re top pic above
    Yes Johny, I had to deal with that too on the one I bought many years ago. This is how much I had to remove for stage II or III turbine housing cut.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_1315.JPG 
Views:	80 
Size:	1.09 MB 
ID:	66267   Click image for larger version. 

Name:	IMG_1321.JPG 
Views:	78 
Size:	1.60 MB 
ID:	66268   Click image for larger version. 

Name:	IMG_1312.JPG 
Views:	76 
Size:	1.11 MB 
ID:	66269  

  6. #6
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    x x x
    Last edited by Dr. Johny Dodge; 04-07-2023 at 06:28 PM.

  7. #7
    Mitsu booster
    Join Date
    Jul 2015
    Location
    Chesapeake, VA
    Posts
    1

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    Do you still have the manifold and swing valve, if so please send me a PM as I am very interested.

  8. #8

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    Interested in the tu header only, if you want to sell separately

  9. #9
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    ok, FINALLY got myself back online

    sorry all for "dropping out" .. been dealing with the issue of being broke ,no internet, having a phone that's so stuffed with updates it "bricks up in hours after reset .. and an executor/trustee for my parents estates that I haven't heard a word out of for almost two years..

    and, pay pal..I think I have that working properly , again

    been a sxxx show of a summer here ..

    I still have the above parts .. and will follow up with those who expressed interest in the order they did so..

    there are a couple of PM's in my box I need to catch up on ..


    and first, turbine housing appears to be machined out to a cavity / bore size of 57mm

    measured with a good metal ruler , sweeping it across the opening from two diagonal measurements at 55mm it shows a "sweep that goes 57mm, inside edge to inside edge when the point of "straight across the hole" is found

    my caliper has gone..missing

    small piece of advice.. never choose a family member as executor or trustee for your estate.. this you and your beneficiaries will benefit from ..IF you hire a lawyer to assume the responsibilities

  10. #10
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    am separating parts.. shadow swing valve is pending, manifold and turbine housing are still available

    turbine housing measures at 57 mm opening

    manifold comes with TU parts kit

    turbine housing comes with required spacer rings for center section mounting and
    the snail shell has been smoothened internally

    asking TU price of $475 us for manifold + shipping and p-p fee

    $175 + shipping & p-p fee for turbine housing

  11. #11
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    swing valve is sold

  12. #12
    Mitsu booster
    Join Date
    Jul 2010
    Location
    Pennsylvania
    Posts
    30

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    Hi,

    Is TU Header still available?




    Quote Originally Posted by Dr. Johny Dodge View Post
    am separating parts.. shadow swing valve is pending, manifold and turbine housing are still available

    turbine housing measures at 57 mm opening

    manifold comes with TU parts kit

    turbine housing comes with required spacer rings for center section mounting and
    the snail shell has been smoothened internally

    asking TU price of $475 us for manifold + shipping and p-p fee

    $175 + shipping & p-p fee for turbine housing

  13. #13
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: TU manifold .63 TN for dbb and "shadow" 3 inch s-w

    sorry all three pieces are sold

Similar Threads

  1. What exactly is "sealer 3419115"?? - exhaust manifold install
    By ohlarikd in forum Engine - Block, Piston, Heads, Intakes
    Replies: 13
    Last Post: 04-03-2011, 11:31 PM
  2. 11" Inch Brakes and 15" Crabs...
    By SpoolinGLH in forum Suspension, Brakes, Wheels, Traction
    Replies: 12
    Last Post: 05-05-2009, 10:27 PM
  3. Wheels/Tires 15 inch Dodge "pumper" wheels $40 (all four)
    By Turbo Uno in forum Parts For Sale
    Replies: 6
    Last Post: 09-25-2008, 07:43 PM
  4. 3" to 5" steel tube transition for custom manifold
    By Ondonti in forum Engine - Block, Piston, Heads, Intakes
    Replies: 0
    Last Post: 06-02-2006, 06:36 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •