Results 1 to 5 of 5

Thread: 86 Turbo Z Coolant Line question

  1. #1
    boostaholic
    Join Date
    Dec 2005
    Location
    Ewing, NJ
    Posts
    1,181

    86 Turbo Z Coolant Line question

    Hello All!
    It has been awhile for me posting here. I've been tied up with my new toy the past couple years, a 78 Dodge van B200 I'm fixing up. Anyway, the oil seals on my turbo went in my 86 Turbo Z all stock setup (probably due to age, and me not knowing I shouldn't run fully synthetic oil in an engine this old). Anyway, ever since I bought this car, due to the aftermarket turbo cooling line from FWD or Turbos Unleashed, the stainless steel tube which comes out of the thermostat housing and runs back to the turbo, does not hug the side of the cylinder head like the factory lines do. This prevents the factory TI airbox bracket from being installed. It has had a K&N cone filter on it since I've owned it and I hate it. I really want to put the factory air box back in, and now is the time to do it. Is this cooling line the wrong one, or is it installed backwards or something? OR does anyone know of a different line that is still available today?
    Thanks in advance for the advice!
    Lee

  2. #2
    turbo addict
    Join Date
    Dec 2006
    Location
    MPLS, MN
    Posts
    3,550

    Re: 86 Turbo Z Coolant Line question

    How would we know if you have it installed correctly without seeing it? Pics often say a thousand words. I do remember many of the early FWDP coolant lines I installed weren't made quite right. IMO, too many adapters, too long, and bends quite not in the correct place. I also remember some of the fittings from some of the vendors were made in China. I always made up my own from name brand AN lines & fittings, or used the factory lines. Those fit perfect. Most people don't bother, because it would require looking up part #'s, ordering, and assembling. Often you get what you pay for...

  3. #3
    turbo addict
    Join Date
    Dec 2005
    Location
    Spokane, Wa
    Posts
    9,046

    Re: 86 Turbo Z Coolant Line question

    I've seen a set where it didn't hug the head very close. Figure out how much distance you need to take off one leg, go to a hydraulic hose shop and they should be able to modify or just make you a whole new piece for cheap.

  4. #4
    Supporting Member Turbo Mopar Contributor GLHS564's Avatar
    Join Date
    Jan 2021
    Location
    Tampa
    Posts
    30

    Re: 86 Turbo Z Coolant Line question

    I just went through the same thing and realized that the coolant hard line with the 90* bend can go on with either end connected to the T-Stat housing. One way the line is TIGHT against the end of the head, and if you flip the line over and use the other end to the T-Stat housing, it gave me plenty of room to add the air cleaner bracket. In a nut shell, the lengths after the bend are two different lengths. Might want to consider flipping the hard 90* line and see what happens.

  5. #5
    boostaholic
    Join Date
    Dec 2005
    Location
    Ewing, NJ
    Posts
    1,181

    Re: 86 Turbo Z Coolant Line question

    Quote Originally Posted by GLHS564 View Post
    I just went through the same thing and realized that the coolant hard line with the 90* bend can go on with either end connected to the T-Stat housing. One way the line is TIGHT against the end of the head, and if you flip the line over and use the other end to the T-Stat housing, it gave me plenty of room to add the air cleaner bracket. In a nut shell, the lengths after the bend are two different lengths. Might want to consider flipping the hard 90* line and see what happens.

    Thank you all for the replies. Yes a picture is worth a thousand words. I didn't have a picture at the time of that writing. I do recall attempting to flip the tube around, with no luck in the past. Going to a hydraulic shop is a great idea, worst case for me. I do have a picture now, but the last time I was active on here, I think we were loading photos onto Photobucket, then linking to that website. I'll try to figure out how to post up photos
    Thanks,
    Lee

Similar Threads

  1. Turbo oil/coolant line replacement
    By 83scamp in forum Turbos & Intercoolers!
    Replies: 3
    Last Post: 06-19-2016, 03:20 PM
  2. Turbo coolant line around head
    By shackwrrr in forum Turbos & Intercoolers!
    Replies: 5
    Last Post: 03-12-2016, 11:56 PM
  3. Replies: 1
    Last Post: 08-01-2014, 11:29 AM
  4. Turbo coolant return line
    By MoparN75 in forum "I need help!"
    Replies: 1
    Last Post: 07-05-2013, 01:42 AM
  5. Replies: 14
    Last Post: 05-23-2012, 10:09 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •