Results 1 to 7 of 7

Thread: I have this situation.

  1. #1
    Authorized Vendor Turbo Mopar Vendor jeff1234's Avatar
    Join Date
    Mar 2006
    Location
    Albany Wisconsin
    Posts
    1,027

    I have this situation.

    The engine is popping through the exhaust at idle and decel. I have read that this indicates retarded exhaust timing. I recently changed over to pt cruiser adjusters. All timing marks aligned as per factory manual both before and after running. Timing seemed to be more touchy than before and starting from cold the engine struggled to run until I gave it more throttle after which it idled properly once some heat built in the engine. On the street the car performs well. I suspect that the cam is off by one tooth. If you agree, then I need to move the cam one way or the other but I am confused as to which way to turn it. I have the cam tensioner tool so I should be able to do this without removing all the front dress on the engine.
    So, which way should I turn the cam, clockwise or counter clockwise?
    The only substitute for cubic inches is cubic dollars, how fast can you afford to go?

  2. #2
    turbo addict
    Join Date
    Mar 2014
    Location
    Toronto Canada
    Posts
    1,772

    Re: I have this situation.

    clockwise would advance the cam
    counter clock wise will retard it

  3. #3
    Super Moderator Turbo Mopar Staff 135sohc's Avatar
    Join Date
    Aug 2008
    Location
    SoMd
    Posts
    6,186

    Re: I have this situation.

    When you got the timing marks set did you use a mirror to check the camshaft sprocket marks/arrows were dead-on aligned with the seam line in the cylinder head ?
    1994 Shadow Sedan. 2.2 N/A, A568 400,000 miles. "the science experiment"
    1987 Shelby CSX #418. Long term rebuild and restore ?

  4. #4
    Authorized Vendor Turbo Mopar Vendor jeff1234's Avatar
    Join Date
    Mar 2006
    Location
    Albany Wisconsin
    Posts
    1,027

    Re: I have this situation.

    my cam gear has an oval slot that when I completed the work was pointed straight up in li e with the top rib on the valve cover. I didn't look at the parting line on the head but I will double check. Because nothing else changed except the adjusters, it's either them or the timing. Has anyone else had this experience with pt adjusters?

    - - - Updated - - -

    Thanks!
    The only substitute for cubic inches is cubic dollars, how fast can you afford to go?

  5. #5
    Authorized Vendor Turbo Mopar Vendor jeff1234's Avatar
    Join Date
    Mar 2006
    Location
    Albany Wisconsin
    Posts
    1,027

    Re: I have this situation.

    Well, Checked it out this afternoon. Sure enough, the cam gear needed to be moved clockwise two teeth. Got it back together and tested it. Runs like it should, needed retiming and the cold stumble and struggling idle are good. Thank you or pointing me in the right direction.
    Jeff
    The only substitute for cubic inches is cubic dollars, how fast can you afford to go?

  6. #6
    Supporting Member Turbo Mopar Contributor
    Join Date
    Feb 2015
    Location
    toronto
    Posts
    1,776

    Re: I have this situation.

    Congrats!
    Regards,
    Miles

    DD '87 Sundance T1, SLH with rear disks
    '87 CSX #432 2.5 CB TII, SLH

  7. #7
    Authorized Vendor Turbo Mopar Vendor jeff1234's Avatar
    Join Date
    Mar 2006
    Location
    Albany Wisconsin
    Posts
    1,027

    Re: I have this situation.

    Thanks Miles.
    The only substitute for cubic inches is cubic dollars, how fast can you afford to go?

Similar Threads

  1. IAC situation
    By HemiShelby in forum "I need help!"
    Replies: 8
    Last Post: 02-14-2010, 11:11 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •