Results 1 to 8 of 8

Thread: Putting 3.05 ring and pinion in an A413

Hybrid View

  1. #1
    Mitsu booster
    Join Date
    Oct 2018
    Location
    Minnesota
    Posts
    33

    Putting 3.05 ring and pinion in an A413

    I have ordered 2 separate (20/61) 3.05 ring and pinion sets. Neither of them seem to mesh together. Has anyone had any experience with this.Click image for larger version. 

Name:	17968.jpeg 
Views:	122 
Size:	667.9 KB 
ID:	64610

  2. #2
    Mitsu booster
    Join Date
    Oct 2018
    Location
    Minnesota
    Posts
    33

    Re: Putting 3.05 ring and pinion in an A413

    I cant find any transmission place that has the 3.05 ring and pinion I need so I will be checking scrap yards does anyone know an easy way to check if a vehicle has the parts without pulling the cover and counting gears?

  3. #3
    Super Moderator Turbo Mopar Staff contraption22's Avatar
    Join Date
    Dec 2005
    Location
    Havertown, PA
    Posts
    9,517

    Re: Putting 3.05 ring and pinion in an A413

    1st gen Neons with the DOHC engine should have a 3.05 ring and pinion.
    Mike Marra
    1986 Plymouth Horizon GLMF "The Contraption" < entertaining sponsorship offers
    Project Log:
    http://www.turbo-mopar.com/forums/showthread.php?69708-The-Contraption-2013-14&highlight=

  4. #4
    turbo addict
    Join Date
    Dec 2006
    Location
    MPLS, MN
    Posts
    3,589

    Re: Putting 3.05 ring and pinion in an A413

    Kevin,
    As mentioned earlier in another thread, the sales codes listed on the radiator tags third line (from bottom) will list what final drive and what transfer gears are in the transmission (lines 18-20). Life is too short to pull off a bunch of diff. and end plates to see what you've got.
    Todd

  5. #5
    Mitsu booster
    Join Date
    Oct 2018
    Location
    Minnesota
    Posts
    33

    Re: Putting 3.05 ring and pinion in an A413

    I finally found a set of gears that will work. I found that the rings and pinions come with different grooves in the gears and only certain ones will fit together correctly. After ordering from 4 different transmission places I found that a 3 groove pinion or transfer shaft will match to a 1 groove ring gear and that a 0 groove pinion fit the 3 groove ring gear.

  6. #6
    turbo addict
    Join Date
    Jan 2006
    Location
    Hazelwood, MO
    Posts
    6,566

    Re: Putting 3.05 ring and pinion in an A413

    Strange that there's a tooth angle change...wonder why?

  7. #7
    Mitsu booster
    Join Date
    Oct 2018
    Location
    Minnesota
    Posts
    33

    Re: Putting 3.05 ring and pinion in an A413

    I am not sure why the angle would be different I cant find any information about compatible gears vs. The grooves
    Click image for larger version. 

Name:	Screenshot_20200205-084416_Email.jpg 
Views:	85 
Size:	495.5 KB 
ID:	64640

  8. #8
    Mitsu booster
    Join Date
    Oct 2018
    Location
    Minnesota
    Posts
    33

    Re: Putting 3.05 ring and pinion in an A413

    Has anyone made a retainer for the transfer gear nuts? Any photos?

Similar Threads

  1. Any way to id ring and pinion
    By Mr overkill in forum Transmission
    Replies: 1
    Last Post: 03-03-2017, 01:26 PM
  2. Transmission 3.77 ring and pinion
    By shackwrrr in forum Parts Wanted
    Replies: 1
    Last Post: 02-08-2017, 01:29 PM
  3. 3.05 ring and pinion
    By T1 woodywagon in forum Transmission
    Replies: 0
    Last Post: 09-24-2013, 11:06 PM
  4. Transmission 413 ring and pinion 3.05-1
    By Rampage16V in forum Parts Wanted
    Replies: 11
    Last Post: 01-30-2009, 10:07 PM
  5. A413 Ring/Pinion fit Neon Trans?
    By ShelGame in forum Transmission
    Replies: 9
    Last Post: 03-16-2006, 11:38 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •