Results 1 to 7 of 7

Thread: Putting a DSM CAS onto the distributor?

  1. #1
    turbo addict
    Join Date
    Dec 2005
    Location
    Mesa, AZ
    Posts
    7,350

    Putting a DSM CAS onto the distributor?

    I came across this for a Volvo and it seems it can be easily adapted to a Dodge distributor?
    https://yoshifab.com/store/billet-re...s-adapter.html


    Then you can go aftermarket ECU with sequential injection with COP.

  2. #2
    Basic Vendor (MSD, Hawk, etc) Turbo Mopar Contributor rbryant's Avatar
    Join Date
    Dec 2005
    Location
    Phoenix, AZ
    Posts
    3,493

    Re: Putting a DSM CAS onto the distributor?

    I actually have provided an adapter for the 420a/SRT4 engine...

    http://rbryant.freeshell.org/420a_cam_adapter.htm I have a couple of them in stock.

    The guy made over 700hp on the dyno which is/was the record for a 420a using my adapter.

    Some of his videos show the prototype version where the bolt holes were slightly misplaced so it was rotated past the slot in the DSM sensor (this is now fixed).

    https://youtu.be/fDdIjWpBgWA

    -Rich

  3. #3
    turbo addict
    Join Date
    Dec 2005
    Location
    Mesa, AZ
    Posts
    7,350

    Re: Putting a DSM CAS onto the distributor?

    Nice! If there is a demand, what do you think the price point would be for an adapter for the 2.2/2.5 distributor position?

  4. #4
    Basic Vendor (MSD, Hawk, etc) Turbo Mopar Contributor rbryant's Avatar
    Join Date
    Dec 2005
    Location
    Phoenix, AZ
    Posts
    3,493

    Re: Putting a DSM CAS onto the distributor?

    Quote Originally Posted by tryingbe View Post
    Nice! If there is a demand, what do you think the price point would be for an adapter for the 2.2/2.5 distributor position?
    Will the DSM CAS fit on a 2.2/2.5 directly centered over the stock distributor drive shaft in place of the distributor? This is with the distributor shaft cut down to be below the surface of the distributor base where the HEP mounts.

    If it will then it would be pretty easy, if not then it would be difficult.



    -Rich

  5. #5
    turbo addict
    Join Date
    Dec 2005
    Location
    Mesa, AZ
    Posts
    7,350

    Re: Putting a DSM CAS onto the distributor?

    I don't know, someone else will have to figure it out as I don't have a CAS.

  6. #6
    turbo addict
    Join Date
    Aug 2009
    Location
    Myrtle Beach, SC
    Posts
    2,133

    Re: Putting a DSM CAS onto the distributor?

    This 1.6 Miata I have here uses a similar setup. It even has the Mitsubishi logo on the CAS.

  7. #7
    turbo addict
    Join Date
    Aug 2009
    Location
    Myrtle Beach, SC
    Posts
    2,133

    Re: Putting a DSM CAS onto the distributor?


Similar Threads

  1. putting in a 2.5L into a 2.2 set up
    By LeBaronMike in forum Engine - Block, Piston, Heads, Intakes
    Replies: 5
    Last Post: 03-26-2012, 12:48 PM
  2. putting spacers on my car
    By lebaronman87 in forum Suspension, Brakes, Wheels, Traction
    Replies: 1
    Last Post: 04-15-2009, 01:19 AM
  3. Putting in new rings..how, and what else should be done?
    By kleiner in forum Engine - Block, Piston, Heads, Intakes
    Replies: 10
    Last Post: 08-18-2008, 10:07 PM
  4. Putting 2.2 in a 2.5 TBI
    By tvanlant in forum Engine - Block, Piston, Heads, Intakes
    Replies: 3
    Last Post: 08-02-2007, 12:08 AM
  5. Putting a 89 cb into an 86 Omni
    By omni_840 in forum Engine - Block, Piston, Heads, Intakes
    Replies: 3
    Last Post: 08-31-2006, 09:06 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •