Hey everyone,
I've had this car just over 15 years and have spent much time & money modifying and restoring it. The idea for the car was to essentially build a prototype Daytona Shelby with mostly parts found in the available parts bin at the time, which you can see from the modification list. I've still got much to do, especially in the restoration part, I will try to update this as I go.
1991 Chrysler Daytona Shelby (Canadian Spec) *G74 VIN code*
Bright White monotone exterior
2.5L High Torque turbo engine
A-568 large spline manual transmission
All black cloth interior with all power options
Factory Sunroof
As some will know, this year only produced 1231 Daytona Shelby's, minus IROC model, minus automatics, minus sunroof, minus the interior options, minus exterior, and finally being Canadian spec'd.
I would venture to say that my particular car could be a 1 of 1 or possibly less then a handful made.
Engine Modifications
Bottom End
90' Common Block "C" Casting
Removed Balance Shafts
ARP Main Studs
Meiling High-Volume Oil Pump
2.2L Common Block Oil Pan/Oil Pick Up/Dip Stick Tube
Balanced Rotating Assembly
.040 Wiseco Forged Pistons
TII Forged Rods shotpeened
ARP Wave-loc Rod Bolts
Top End
90' Casting 782 Cylinder Head
Ported & Polished by Rolling Thunderz
+1mm Over Sized S/S Valves with 3 Angle Valve Job
MP Hardened Keepers/Viton Seals/Valve Springs
89'+ Stock Turbo Camshaft
87' Two-Piece Intake Ported & Polished
Ported & Polished Exhaust Manifold
Stock 46mm Throttle Body
ARP Head Studs
MP 5281064 Headgasket
Relentless Performance Adjustable Cam Gear
Turbo/Intercooler
T04B .60 A/R Compressor Housing with T04E 50 Trim Wheel
.63 A/R Turbine Housing with Stage II Wheel
10lb Spring Adjustable Wastegate
3in Custom made swing valve
3in Custom made S/S down pipe and full cat back
Magnaflow S/S High-Flow Catalytic Converter
Magnaflow S/S Bullet style muffler
Custom Tripple TII Stock Core Intercooler
2in Custom made lower charge pipe
2.5in Custom made upper charge pipe
Turbo XS Blow-Off Valve
3in Custom made intake with Spectre filter
Custom Radiator Overflow Can
Catch can PCV system (closed)
S/S Braided Turbo & Coolant Lines
Vibrant Silcone Vacuum Hoses
Powerfist Vacuum Block
Engine Electronics/Fueling/Cooling
MSD 6AL Ignition System
MSD Blaster Coil
Rbryant MSD 8.5mm Ignition Wires
Rbryant HEI Distributor Cap
NGK BPR6EIX Spark Plugs
Super 60 Injectors
TU Billet Fuel Rail
Universal Accufab Adjustable Fuel Regulator
Russell -6AN Fuel Lines/Fittings
90' Gas Tank with Walbro 255 l/hr Fuel Pump
Spectra Premium Full Size Turbo I Radiator
TU Thermostat Housing
Stant 180 Degree T-stat with 1/16 Hole
Flex-A-Lite 16in Cooling Fan
Removed all A/C components
Polybushings.com Alternator Bushings
160 AMP Alternator (Bryan)
TU Custom SBEC 3BAR calibration
Block & Intake Painted Ford/Shelby Blue
Polished Valve Cover
Transmission Modifications
90' Rebuilt Large Spline A-568 with A-523 3.50 FD
Block style LSD with clutch discs and HD springs
Polybushings.com Adjustable Bobble Strut
Booger Poly Shifter Bushings
TU Ultimate 6-Puck Ceramic Clutch (Stage II)
Suspension/Brake/Wheel Modifications
Eibach Pro-Kit Springs, Uncut
Koni Adjustable Front Struts & Rear Shocks
Polybushings.com Front Motor, Passenger, and Transmission Mounts
Polybushings.com Front Control Arm Bushings
Polybushings.com Rear Axle to Frame Bushings
MOOG Poly Front Sway Bar Bushings
Polybushings.com Rear Sway Bar
CS Racing Rear Adjustable Panhard Bar
KVR Performance Front Cross-Drilled Rotors/Stock Rear
FWD-P S/S Braided Brake Lines
Front Polished Strut Bar with Covers to fit
Hawk Performance Front/Rear Brake Pads
5Zigen FN01R-C Wheels (17x8,+35mm Offset, 16.9lbs) custom match painted w/ machined lip
Custom Pentastar Center Cap
245/40/17 BFG KDW Tires
Interior Modifications
FWD-P A-pillar Gauge Pod
Autometer Mustang center gauge Pod
Autometer Phantom 2/16 Elec. Engine Temp.
Autometer Phantom 2/16 Elec. Oil Press.
Stewart Warner 3 3/8 Tach
Autometer Shift Light
Autometer Phantom 2 5/8 Boost (30psi)
Autometer Phantom 2/16 EGT
Autometer Phantom 2/16 Volts
AEM UEGO Wideband
90' Lebaron Traveller 2-Button Computer
JVC Kamaleon CD Deck
Complete Infinity Kappa/Reference Series Speakers/Subwoofer
Kenwood 600W and 350W Cross-over amps
Exterior Modifications
Removed all side striping
Positive Impressions Windshield/Rear Window Decals
Tinted windows all around
"Intercooled Turbo" Hood decal
Custom front/side/rear Shelby decals
S10 Lower Airdam
My thanks go out to all the vendors and micro-vendors who make our community possible, also to thank those who provided hours and hours of tech advice!! More pics in my gallery, if you wanted to see them.