Results 1 to 2 of 2

Thread: 4 core radiator. All brass construction!

  1. #1
    turbo addict
    Join Date
    Dec 2006
    Location
    MPLS, MN
    Posts
    3,589

    4 core radiator. All brass construction!

    Date: 27th March 2015
    Username: 4 l-bodies
    Full Name:Todd Nelson
    City, State, Zip: Bloomington, MN 55431
    Contact: PM me for phone #.
    Price: sold shipped or best reasonable offer

    Description:
    Selling one of a kind custom made ultimate duty ALL BRASS 4 CORE RADIATOR. This is virtual bolt in for Chrysler 87-89 TII G/H/J/Q bodies. This can be used with or without factory TII intercooler. Can obviously be used with a FMIC as well. Even the stock fan shroud provisions are there. Can be easily made to fit other earlier bodies including L-body with top and bottom tab relocation. This should be very simple to modify as mounting tabs are soldered in place. Top, bottom, tanks, inlet, outlet, filler neck, core, everything except mounting tabs and intercooler mounting fasteners are ALL BRASS. Even the factory brass radiators do not have top and bottom plates made of brass. Passenger side tank modified to fit even the biggest 120 amp alternator. Bought this thinking to put it in my Omni, but decided to go another route. This has probably been installed and ran for a very short time, perhaps not though. Unfortunately I do not have any history on this at all. Not sure who made this but they obviously were a master at their craft. I have pressure checked this and submerged in water and it is sealed perfectly. It was then carefully dried. Being brass and four core, this is no lightweight radiator. It is 16 lbs, which is 5+ lbs heavier than factory two core brass radiators. On the plus side, it should last a very, very, long time. I would have painted it, but no one would have believed it to be all brass construction. It does have some minor shelf wear to fins only in couple spots on inboard side of core. No tube damage. This was probably made a very long time ago. No one that I know of today uses brass construction for custom radiators because of the high cost.
    So if you’re looking to cool a high horsepower Chrysler turbo car, or want an overkill radiator, this one should fit the bill. Core dimensions are 15.5 x 19.25 x 2.25” Overall dimensions are 17.25 x 21.75 x 2.5”. Core is 3” wider than TII core and about 1” thicker.
    Looking for $ sold shipped or best reasonable offer. This would be at least a grand to duplicate today.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_7071.JPG 
Views:	120 
Size:	320.2 KB 
ID:	54153   Click image for larger version. 

Name:	IMG_7067.JPG 
Views:	104 
Size:	304.1 KB 
ID:	54154   Click image for larger version. 

Name:	IMG_7065.JPG 
Views:	97 
Size:	342.4 KB 
ID:	54155   Click image for larger version. 

Name:	IMG_7073.JPG 
Views:	102 
Size:	122.2 KB 
ID:	54156  
    Last edited by 4 l-bodies; 04-03-2015 at 11:00 AM. Reason: marked sold

  2. #2
    turbo addict
    Join Date
    Dec 2006
    Location
    MPLS, MN
    Posts
    3,589

    Re: 4 core radiator. All brass construction!

    Radiator is sold. Thanks for looking.
    Todd

Similar Threads

  1. Aluminum 3 core ebay Radiator from Honda
    By southkurtk in forum Engine - Block, Piston, Heads, Intakes
    Replies: 5
    Last Post: 10-01-2009, 05:28 PM
  2. brass coolant fittings
    By kwiksilver in forum Turbos & Intercoolers!
    Replies: 11
    Last Post: 05-16-2009, 07:45 PM
  3. brass press fit fittings
    By WickedShelby88 in forum Maintenance & General Tech
    Replies: 2
    Last Post: 04-14-2008, 11:52 AM
  4. Pinks/Possible car construction? To whip those V8 POS's
    By guyd_15 in forum Events, Racing, & Results!
    Replies: 10
    Last Post: 03-07-2006, 11:59 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •