Results 1 to 6 of 6

Thread: FS/FT 1987 Dodge Daytona Shelby Z project

  1. #1
    turbo addict
    Join Date
    Sep 2006
    Location
    Indianapolis, IN
    Posts
    2,793

    FS/FT 1987 Dodge Daytona Shelby Z project

    Date: 19th January 2015
    Username: moparman76_69
    Full Name: George Manning
    City, State, Zip: Indianapolis, IN
    Contact: PM, will supply phone and email
    Selling or Wanted Price: 800 OBO with the parts I have included, I'll continue working on it as I still have it and the price will reflect that
    Description: 1987 Dodge Daytona Shelby Z

    I've got the previous issues resolved in a way, the AIS is for now disabled and the car idles at 900-1000 rpm. I've decided to pass this on as a good start for a project so I can put the money back into finishing the van finally.

    2.2/A555 Has a TII one piece and Garrett turbo

    Entire brake system was replaced recently including new hardlines
    Large FMIC
    Accufab rail mount AFPR
    Innovate LC-1 with Red DB-2 gauge
    Has the TII radiator but not the factory intercooler.
    2.5" downpipe with 3" exhaust and magnaflow muffler
    The headlight motors still work
    I put the set of Monroe struts with 1 coil cut off springs I had on the van on the front

    What it needs ASAP

    The power steering pump has been removed and the lines looped at the rack
    The front end needs bushings and an alignment
    It still has the 87 style rear discs and the e brake was never reconnnected
    The battery currently in the car goes to my truck, I'll be pulling it out before the car is sold.

    Again 800 and I'll include the following

    6 bolt AL flywheel
    A520 3.5 final with a moly plate installed
    A different one piece gasket valve cover since the one on it appears to need the baffle resealed
    A poly front motor mount
    Ebay BOV with adapter pipe to replace the Talon valve that is crushed too far to work properly.
    Spirit R/T rack that has been in my attic for two years, I can probably dig up a P/S pump and bracket so the power steering can be hooked back up
    I have a set of 6.5 crabs that can go with the car, the tires on them are bald. I'd need to keep the wheels on the car now if you wanted them so I can keep that car a roller.


    The car will run and drive but I wouldn't want to take it on a long road trip home, I'd say you'd need to tow it home. The car that has the crabs on it is an 89 sundance with no title. I could work a hell of a deal for you if you wanted both cars and a load of parts to take home.











    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_20141027_152806_zpslvepzkyk.jpg 
Views:	81 
Size:	61.5 KB 
ID:	52748  
    Last edited by moparman76_69; 03-26-2015 at 11:04 AM.

  2. #2
    turbo addict
    Join Date
    Sep 2006
    Location
    Indianapolis, IN
    Posts
    2,793

    Re: FS/FT 1987 Dodge Daytona Shelby Z project

    Bump, I updated the first post to reflect the current condition.

  3. #3
    turbo addict
    Join Date
    Sep 2006
    Location
    Indianapolis, IN
    Posts
    2,793

    Re: FS/FT 1987 Dodge Daytona Shelby Z project

    Bump again, I need this thing gone.

  4. #4

    Re: FS/FT 1987 Dodge Daytona Shelby Z project

    Is all the interior present and matching? In the picture it looks like the passenger seat is missing and the dash is a different color...

  5. #5
    turbo addict
    Join Date
    Sep 2006
    Location
    Indianapolis, IN
    Posts
    2,793

    Re: FS/FT 1987 Dodge Daytona Shelby Z project

    It went missing at some point. I installed a XSpower intercooler with the same side inlet/outlet to replace the ebay one with the miles of piping, I also replace the non-functioning BOV with a ebay type RS knockoff. I have to set the boost controller so it won't hit cutoff and most all of the bugs with the running part have been worked out. If it doesn't sell in the next week, I'll end up keeping it at least through the summer and putting a set of tires on it.

  6. #6
    Moderator Turbo Mopar Staff Vigo's Avatar
    Join Date
    Feb 2006
    Location
    San Antonio,TX
    Posts
    10,798

    Re: FS/FT 1987 Dodge Daytona Shelby Z project

    One good wheelhopping session or a 1-2-1 misshift will finish off that trans case.
    Or a protruding manhole cover for that matter.

    Don't ask how i know.

    Dont push the red button.You hear me?

Similar Threads

  1. Beeble's 1987 Dodge Daytona Shelby Z Project Thread
    By beeblebrox82 in forum Project Log
    Replies: 139
    Last Post: 09-03-2017, 08:44 PM
  2. Replies: 0
    Last Post: 07-14-2013, 11:15 AM
  3. For Sale 1987 Dodge Daytona Shelby Z
    By vxvxAndrewxvxv in forum Cars
    Replies: 2
    Last Post: 07-30-2012, 12:29 AM
  4. For Sale 1987 Dodge Daytona Shelby Z, T-Top
    By Spycker in forum Cars
    Replies: 10
    Last Post: 07-16-2012, 11:03 PM
  5. 1987 Dodge Daytona Shelby Z
    By southkurtk in forum Project Log
    Replies: 39
    Last Post: 11-19-2009, 07:48 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •