Date: 06th September 2014
Username: turboshadow
Full Name:Nathan Doyle
City, State, Zip:Cincy,OH
Contact: PM
Selling or Wanted Price: $2300 OBO
Description: I bought this car from a long time turbo mopar guy in 2012 he had just rebuilt the engine and the car sat around for a while until I bought it. I have auto crossed the car about 10 times and drag raced it a few times. The car took 2nd place at the SDAC 23 Autocross on the old suspension and smaller slicks. The car has seen little street use. This is a 12 second car all day and would make it into the 11s on a good day. It has a custom cal made by the previous owner to run about 28psi, I currently have a grainger valve on it set to 20psi. The car is overall rust free and what rust it did have was repaired, the floors are in perfect shape. The paint is in typical original condition and the car does have some dents and dings it is by no means a show car. The front airdam and fender extensions are currently off the car in order to get my 275 tires to fit and to make it easier to put the car on a tow dolly. Wiper bushing is fubard at the moment. Car has 149k.
I can included my 15x10 diamond race wheels with 275/35 Hooiser R6 Slicks and 6.5 Crabs with 205/50 A6 Hoosier tires for some additional $$$.
2.2 Common block with about 3k on rebuild
2.2 forged steel crank turned .01/.01
2.2 forged rods resized with ARP Wavelock bolts
.020 Mahle Pistons
.020 hand ground ZeroGap rings
Melling high volume oil pump
Ishihara-Johnson crank scraper
Clevite 77 main and rod bearings
New intermediate shaft bushings
Advanced Auto Alternator and Power Steering Pump
Cylinder 4 cooling mod
185 Thermostat
MP 006 Head Gasket with Copper shim
3 intake with K&N
FB crossdrilled head stock valves-gasket ported w/Singh grooves-bronze guides
LRE ported exhaust manifold
87 2 piece intake with 52mm throttle body
FWD performance billet fuel rail w/52lb injectors and fuel pressure gauge
Accufab adjustable fuel pressure regulator
Walbro 255
Custom PCV- exhaust vent with catch can
Adjustable cam gear
FWD Performance F4 roller cam w/spacers
FWD Motion HD valve springs
TBI dual port valve cover w/baffle and o ring gasket
3bar MAP sensor and custom cal with ZIF socketed computer
50 Trim T3/T4 hybrid stock compressor housing turbo w/.63 stage 3 turbine wheel/housing
3 RP swingvalve with t-bolt clamp to custom 3 side exit
2 ½ intercooler piping with Turbo XS RFL
3 Mishimoto intercooler front mount
12 Radiator fan
MP right side and front engine mounts
Custom solid rear motor mount
Stock flywheel
McLeod Rev-lok clutch
94 a523 trans w/3.50 diff gear
Automatic Omni axles
BlackTrax posi block
Shadow shifter cables
Neon short shifter
Various autometer gauges
LC-1 wideband o2 sensor with Moates.net o-meter
88 Shelby Z front brakes and rotors with larger master cylinder
Newer front rubber brake lines, calipers, and wheel cylinders
Uerthane bushings in all front including tie rod ends
Seam welded K-Frame
Grant GT steering whell with adapter and extender
Rollcage 4 point installed have rest of cage for 6 point
Front Monroe Struts with cut MP Road Race Springs
Rear Konis with cut Stock Springs
New 5 point driver side harness
Click here to view the original image of 960x540px and 80KB.
Click here to view the original image of 960x540px and 112KB.
Click here to view the original image of 960x540px and 38KB.
Click here to view the original image of 960x540px and 65KB.
Click here to view the original image of 960x540px and 96KB.
Click here to view the original image of 960x540px and 49KB.
Click here to view the original image of 960x540px and 63KB.
Click here to view the original image of 960x540px and 39KB.
Click here to view the original image of 960x540px and 57KB.
Click here to view the original image of 960x540px and 62KB.
Click here to view the original image of 960x540px and 61KB.
Click here to view the original image of 960x540px and 71KB.
Click here to view the original image of 960x540px and 60KB.
Click here to view the original image of 960x540px and 160KB.
Click here to view the original image of 960x540px and 38KB.