Misc. T3 Parts

[Will Martin]

Date: 24th August 2014
Username: Will Martin
Full Name: Will Martin
City, State, Zip: Fairfield, CA
Contact: PM Please
Price: Various
Paypal: mgouki@hotmail.com
Description:
I'm clearing out all of my TD parts, which mostly consist of T3 parts. I'm a little out of touch with the TD sceen last two years, so please forgive my prices if they're a bit high. I'm opening boxes and totes of things I didn't know I had. Pictures of items are linked to my Photobucket page. Tons of items to come in the near future-engine parts, heads, turbos, ECUs....<sigh>:

http://s6.photobucket.com/user/mgouk...s%20for%20sale


1) T3 "race" block. All work done by NT Machine Shop in Langley, B.C. +40 over block with all parts balanced, balance shaft hole plugged, Wiseco +40 pistons, rings are not sized, ARP rod and block bolts, new block plugs. Has been sitting for about 5 years, forgot I even had it. Has surface rust on the block and the crank has spotting on it, may need to be repolished. $500 OBO + shipping

2) T3 Dunn casting head with cams. Center plug professionally welded, no cracks. SOLD

3) T3 production casting bare head with valves and springs, no cracks. $300 OBO + shipping

4) T3 block with stock pistons, rods, oil pan, crank. $300 + shipping

5) Two (2) sets of T3 valve covers. $50 EACH OBO + shipping SOLD

6) T3 intake and exhaust manifold. $40 EACH OBO + shipping

7) T3 A-568 large spine differential. $30 OBO + shipping

8) T3 throttle body. $25 shipped

9) T3 water jacket/housing for cylinder head. $50 shipped SOLD

10) T3 rockers and lifters, only have 14 intake/exhaust. $150 shipped

11) T3 intake/exhaust cams. $150 OBO pair shipped

12) T3 intake/exhaust cam sprockets. SOLD

13) T3 flywheel. $75 + shipping

14) T3 Centerforce dual friction clutch with throw-out bearing. $100 + shipping) SOLD

15) OBX differential upgraded bolts and washers $15 shipped

16) T3 Cardone water pump with gaskets $25 shipped

17) T3 Mopar water pump with gasket $30 shipped

18) +40% injectors SOLD

19) +20% injectors, two (2) sets $100 each shipped

20) T3 Camshaft position sensors (2) $40 each shipped SOLD

21) Three 3bar MAP sensors, two with pigtails, one without $40 each shipped ONE WITH PIGTAIL SOLD, ONE LEFT

22) Accufab adj. FPR with Summit racing inline gauge and stock T3 fuel line SOLD

24) T3 ignition coil $40 shipped

25) JDM Ebay intercooler. See my profile for picture of it on my Spirit RT. 3" in/outlet holes, core measures 2.75" wide, 11.75" tall, 23.75" long, comes with cheap aluminum style pipes with clamps-see picture. A little banged up from removing it and a couple bent fins but works fine. $100 + shipping

26) ARP stainless steel studs 400-8015, can be used on T3 exhaust manifolds $50 shipped

I'm working doubles for 4 of the 5 days this week, so please bear with me on responding and shipping, although I should get items out on time.

[ShelGame]

5) Three (3) sets of T3 valve covers. $50 EACH OBO + shipping

I want 1 of these. Shipping to Michigan, 48189?

3) T3 production casting bare head with valves and springs, no cracks. $350 OBO + shipping

I think shipping is going to kill this one for me, but let me know what it would be anyway...

[MNmopar]

I'll take the cams if the lobes all look good. Do you notice any flaking at all?

[Will Martin]

Bump. Lowered prices and added parts.

[minigts]

Any details on the +40s? Miles in use?

[Will Martin]

I bought them used and used them in my Daytona RT for less than 5k miles. I didn't have any issues with my fuel and they've been sitting for about 5 1/2 years.

[minigts]

Thanks Will. I'll PM you tomorrow about them.

[Will Martin]

Testing

[HSKR]

Didn't realize it was OP with the testing post. lol

[HSKR]

Interested in a set of the valve covers and intake manifold.

[Will Martin]

Instead of starting a new thread, I wanted to resurrect this one with new items.

All items can be viewed at my photobucket page.

PM ONLY PLEASE to save thread space

Pay Pal is: mgouki@hotmail.com

No "dibs", first come, first serve.

Prices do not include shipping, buyers are responsible for insurance, Parts sold as is

-LWP ported Stage III head $1,200 OBO. All work was done 12/2006. Head has roughly 500-800 miles on it.
-From Wallace "For comparison a stock head at .300 flowed 191cfm and exhaust 164cfm. We will certainly pick up about 10 additional CFM with a valve job" The above flow numbers were BEFORE valve job.

Comes with the following:
*LWP Stage I cryo treated cams
*FWDP adj. cam gears
*ARP head bolts (have been torqued once)
*Flow numbers (straight from Wallace)
..........Intake....Exhaust
.100... 109.52 ..107.0
.200... 202.40 ..169.4
.300... 258.0 ....209.0
.350... 272.8 ....220.0 ** I had 2 motors die, so
.400... 282.1 I only flowed at 24 in.

*Head smoothed to an RA of 18. Will need to be resurfaced, see small scratch in picture (from removing head).
*Coated valve guides to reduce wear.
*Intake manifold (painted silver) port-matched to 240 cfm (stock is about 220 cfm), opened to accept a 70mm throttle body
*Exhaust manifold port-matched (external coating flaking), tapped for EGT probe
*Cometic .074 head gasket (used once) with spray
*Valve covers (painted silver)
*This head, on my car that wasn't tuned properly, could spin the wheels with a Precision Stage III dual ball bearing turbo in first gear no problem! The car was very fast, one day I took off and left my shadow!

-Precision Turbo Stage III Dual Ball Bearing Turbo $600 OBO
*Has roughly 500-800 miles on it.
*ZERO SHAFT PLAY! Spins smoothly, Mobile One synthetic always used in it.
*Comes with first-gen ATP internal v-band waste gate

-Griffin Radiator with T3 fan $120. Used in my RT. A little banged up from fitting but no leaks, no rust inside. SOLD

-T3 Ground Wire Kit $25

-Computers
*'85-87 2.2/2.5 Power module 5227808 $50
*'92 T3 computer previous owner messed around with it and set it at injector full duty cycle, so when ran in car it floods with fuel. $100
*'89 CSX computer 4516837 $100
*'92 T3 FWDP Stage 1 cal $200
*'89 S60 computer with cracked case, still works $100

[Will Martin]

Head and turbo price reductions!

[Will Martin]

Head reduced to $900

[Will Martin]

Ported head/manifolds combo sold.

[Will Martin]

TIII bare head and ARP exhaust studs sold

- - - Updated - - -

Price Reductions

T3 rockers and lifters, only have 14 intake/exhaust. $100 shipped

T3 intake/exhaust cams. $100 OBO pair shipped

T3 intake/exhaust cam sprockets. SOLD

T3 flywheel. $75 + shipping

OBX differential upgraded bolts and washers $10 shipped

T3 Cardone water pump with gaskets $20 shipped

T3 Mopar water pump with gasket $25 shipped

+20% injectors, two (2) sets $75 each shipped

T3 Camshaft position sensor $30 shipped

Two 3 bar MAP sensors, one with pigtail, one without $40 each shipped

T3 ignition coil $20 shipped

T3 ground wire kit $20

FWDP billet fuel rail with gauge, with braided lines, A/N fittings and connectors to connect to stock lines, Accufab adj. fuel pressure regulator $150

[91dodgespirit]

I'll take the rockets and lifters. PM me your info

[Will Martin]

Updated:
PM only PLEASE!

*Denotes still on car, have to remove

'92 Daytona IROC RT wheels with center caps, straight with no dents or bends $250

T3 exhaust cam $50

T3 intake manifold $10 SOLD

T3 exhaust manifold $10 SOLD

T3 flywheel. $25 SOLD

OBX differential upgraded bolts and washers $10

T3 Cardone water pump with gaskets $10

T3 Mopar water pump with gasket $15

T3 ignition coil $20

T3 ground wire kit $20 PENDING

FWDP billet fuel rail with gauge, with braided lines, A/N fittings and connectors to connect to stock lines, Accufab adj. fuel pressure regulator $125 SOLD

Precision Turbo Stage III Dual Ball Bearing Turbo $450

*A-568 trans. Shifts smooth with no grinding $300

*A-568 shifter cables with Booger bushings and FWDP short throw shifter $150

*T3 block with JE +40 pistons $300 PENDING

*Adjustable panhard bar $40 SOLD

*FWDP SS 3" exhaust with additional cat delete pipe to swap with cat and Borla muffler $200

*Turbovanman (Simon) HID lights $40

*Daytona RT rear brakes (driver's caliper has a striped thread IIRC, can be used as a core) $50

*Wilwood BBK from TCE Performance. Comes with brackets used to mount to RT style knuckles, red calipers with slotted rotors and braided lines, not even 20 miles on them and not broken in. Only used to move car, requires DOT 4 brake fluid $600

*Adjustable Koni struts and shocks (G body) with knob. Have about 10k miles or so on them, but still work great. $300 PENDING

*Eibach (G body) springs. Have about 10k miles or so on them. $150 PENDING

T3 intake snorkel $50

T3 radiator/intercooler with bov and hoses $100

Daytona headlight covers. I don't have the tabs to stick on the car to attach them. Never used, a little scuffed up from sitting $30 SOLD

FWDP '92 RT socketed stage 3 cal for 15-20 lbs of boost $140

[Will Martin]

FYI to all parties;

I'm truly trying to properly "manage" my very limited time from 16 hour work days, playing with my kids and being a husband. Please bear with me on getting to some of this stuff...thanks.

[Will Martin]

I was able to take some pictures of the parts all interested parties. Also, I found some additional parts I'm going to add as well.









Comparison of stock to Wilwood


turbo comparison to stock T3

[Wastelands Warrior]

Parts arrived today. Thanks Willy. Great guy to deal with!