Date: 30th May 2014
Username: DetroitTurbo
Full Name: Frank Daugherty
City, State, Zip: Detroit, Mi 48239
Contact: PM for phone #
Selling or Wanted Price: $5000 or best offer.
Edit: $3500 is my bottom dollar, I have more than that into just the engine. $4000 takes everything, any less and I'm keeping the Lengel upper plenum (you will still get original 2-piece upper).
Description:
Clean Title
Well guys after a long time of trying to get this thing put together, I was almost to the finish line, but I lost my job and now I have to make a turning point in my life and I just can't put anymore money into this car. I'll get right to it and list the pros and cons.
Pros:
Engine:
- Rebuilt 87 engine block with forged wiseco pistons, T2 rods, T2 crank.
- Direct Connection big valve ported G-head (professionally repaired)
- PT lifters
- Comp Beehive springs
- 3800 retainers
- Roller cam
- Rebuilt T2 turbo with 60mm S60 style compressor. (less than 500 miles)
- ARP Head Studs
- MP Head Gasket
- New Timing Belt
- Fidanza adjustable cam gear
- FWD Performance ported exhaust manifold (ceramic coated)
- Ported lower 2-piece runners
- Lengel custom upper plenum
- Accufab AFPR (new)
- FWD Performance Billet Fuel Rail (new)
- +40 Injectors (new)
- Custom MSD wires (new)
- Custom Distributor Cap (new)
- Malory coil (new)
- 160 amp alternator
- Custom fuel pump block off plate
- Acannell's #4 coolant mod
- Stainless braided turbo lines
- FWD Performance billet t-stat housing
- Oil pan sand blasted and painted black
a413 Transmission:
- Direct clutch plates replaced
- Pump gears replaced with 86+ style gears
- New high stall torque converter 86+ style
- New gaskets / filter
Interior:
- Custom 3-gauge plate for dash
- AEM wideband (new)
- Autometer boost/vac (new)
- Glowshift electronic fuel pressure gauge (new)
- Pioneer MVH-P8200BT professionally installed w/ bluetooth
- Kicker 6.5" front
- Kicker 6x8" rear
- Infinity reference 3.5" dash
- Kicker 10" subwoofer in low-profile sealed box
- Rockford Fosgate 125w RMS amp w/ professionally installed Kicker 4 gauge wiring kit
- Interior is black in mint condition. The only blemish in the interior is a small burn hole on the back seat.
- Front seats are in great shape, no wear or tears.
- The bezels, door handle trim, vents, and speaker covers were highlighted with red paint, but I have brand new woodgrain dash bezels and center console, and spare black vents. The rest can be re-painted black.
Other:
- Viper 5901 alarm/remote start 2-way 2-mile remote. professionally installed.
- New wagner pads / AAP rotors
- FWD Performance Stage 5 87 logic module (new)
- 3-bar MAP sensor (new)
- AEM No-weld O2 Sensor mount (new)
- 4x BFGoodrich G-force Sport-Comp II 195/50/15 Tires (new)
- New gas tank & straps
- New 255 lph Walbro pump
- New 2.5" intercooler piping kit
- HKS SSQV on 2.5" pipe with real OEM HKS o-ring/snap-ring
- New big 2.5" in/out same side Intercooler
- 2.5" to 3" 90 silicon elbow and short 3" pipe for K&N filter
- Custom radiator/intercooler mount (takes place of T2 intercooler and brackets)
- New KYB struts all around
- New hatch struts
- Re-finished rear hatch louvers with original hardware
- a-pillar gauge pod
- 3/8" npt bung for Air charge temp sensor relocation to IC piping.
- custom throttle body spacer for vacuum ports
- vacuum block
- FWD Performance red vacuum line kit
- Conventional H4 Headlight conversion with halos
- New belts/hoses
Cons:
- This vehicle is still a project. I have 99% of the parts needed to finish it, but it would take another $200-$300 to get it back on the road for every day use.
- Needs 4 pins switched on logic module to work with 87 computer
- Needs wiring run for 3-bar map
- Needs new gas tank and walbro pump (included) installed (original tank/pump still in car)
- Needs aftermarket gauges installed/wired
- Passenger side front caliper does not move when brake is pressed
- Passenger side front wheel bearing needs replaced
- Light rust underneath, nothing crazy.
- Paint is not perfect, it has a few blemishes and chips, but it is 98% good.
- No battery
For the right price I will include my daytona dealership package; framed daytona poster, daytona match-box and un-cut "Daytona" key + keychain.
I have seen very few first gen Daytona's as nice as this one. It seriously hurts to even make this ad, I really don't want to sell it but I have no choice.
I could be forgetting something because this list is gigantic and I can't remember every part I have for it. If you want more pictures just ask. Make me an offer, the worst I can say is no. I will add pictures of engine bay once engine is back in the car.
Engine after rebuild
Cylinder head after repairs
The lighting was bad in this picture so it looks much lighter than it is.
The light was a bit crooked in this picture but I have adjusted it since
As of 6/11/14 here is the current progress:
front engine mount attached
valve cover installed
upper intake installed
fuel rail, AFPR, and injectors installed
alternator installed
distributor installed