Page 2 of 3 FirstFirst 123 LastLast
Results 21 to 40 of 50

Thread: Part numbers and parts that fit the Consulier

  1. #21
    Supporting Member Turbo Mopar Contributor ForzaV12's Avatar
    Join Date
    Mar 2007
    Location
    the OC
    Posts
    679

    Re: Part numbers and parts that fit the Consulier

    any one figure out what the gas cap is from(some Mopar I'm sure). Mine is bad and after replacing all the fuel lines, sender,etc chasing a gas smell, I realized it was the cap.
    87 GLHS ,66 Hemi Coronet, 69 Road Runner, 70 Challenger-"Vanishing Point", 68 Road Runner "Petty",69 ZL1 Corvette,2016 Scat Pack Challenger,67 Corvette vintage racer,Cadillac ATS Turbo, 66 GTO road racer,67 911S, Ford V Ferrari Porsche 906 and Ferrari P3

  2. #22
    Hybrid booster
    Join Date
    Jul 2013
    Location
    Orlando
    Posts
    496

    Re: Part numbers and parts that fit the Consulier

    pretty sure it's 84 turismo

    Motorad MGC789
    Dayco 84789
    There is a locking version... Stant G-789 10589

  3. #23
    Supporting Member Turbo Mopar Contributor ForzaV12's Avatar
    Join Date
    Mar 2007
    Location
    the OC
    Posts
    679

    Re: Part numbers and parts that fit the Consulier

    Thanks!
    87 GLHS ,66 Hemi Coronet, 69 Road Runner, 70 Challenger-"Vanishing Point", 68 Road Runner "Petty",69 ZL1 Corvette,2016 Scat Pack Challenger,67 Corvette vintage racer,Cadillac ATS Turbo, 66 GTO road racer,67 911S, Ford V Ferrari Porsche 906 and Ferrari P3

  4. #24
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    Just got this.......
    This is for the front shocks for the GTP.

    QA1 acquired Carrera in 2004. The replacement for the 32 Series Carrera shocks would be the 75 Series, part number 7554.
    I does say 7554 on the box, but on the shock it says Q12516....CARRERA...Made in Mexico
    Last edited by Johnny; 05-05-2014 at 01:45 AM.
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  5. #25
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    This is kind of a big deal to me.
    I took my GTP drive axle to a very good CV axle shop.

    He took it apart and measured it.
    It is within 1/16" of a Caravan axle.
    So why did they do the weld on piece?
    Did they not realize then, that a Caravan axle was the same as they were making from what ever they made these from?

    Anyway, he is rebuilding mine for $100 and also making me a new one using a quality shaft for $100.
    So I will have a spare.

    He said he can make the shaft from chrome moly making the cost for each axle at $400.
    If the shaft is the weak point.

    If the joint becomes the issue he can use 930 Porsche joints and the cost is over $1000 per axle.

    Me, I am going to run these until I see any issues happening.
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  6. #26
    boostaholic
    Join Date
    Feb 2012
    Location
    socal
    Posts
    1,241

    Re: Part numbers and parts that fit the Consulier

    Thats great! Check the box on yet another easy to get part.

    So when does she hit the 1320??
    MinivanRider

  7. #27
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    Easy to get but buying "good" ones is not as easy.
    This place builds nice quality parts, not getting the $59 import stuff.

    1320?
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  8. #28
    turbo addict
    Join Date
    Oct 2007
    Location
    Rockville, Md
    Posts
    3,520

    Re: Part numbers and parts that fit the Consulier

    Quote Originally Posted by Johnny View Post

    1320?
    That's racer speak for 1/4 mile Johnny.

  9. #29
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    Really....never heard of that. Must be the foot distance?
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  10. #30
    Hybrid booster
    Join Date
    Jul 2013
    Location
    Orlando
    Posts
    496

    Re: Part numbers and parts that fit the Consulier

    Quote Originally Posted by Johnny View Post
    This is kind of a big deal to me.
    I took my GTP drive axle to a very good CV axle shop.

    He took it apart and measured it.
    It is within 1/16" of a Caravan axle.
    So why did they do the weld on piece?
    Did they not realize then, that a Caravan axle was the same as they were making from what ever they made these from?

    Anyway, he is rebuilding mine for $100 and also making me a new one using a quality shaft for $100.
    So I will have a spare.

    He said he can make the shaft from chrome moly making the cost for each axle at $400.
    If the shaft is the weak point.

    If the joint becomes the issue he can use 930 Porsche joints and the cost is over $1000 per axle.

    Me, I am going to run these until I see any issues happening.
    Is this the passenger or driver side axle that matches the caravan? or both sides? what year caravan?

  11. #31
    boostaholic
    Join Date
    Feb 2012
    Location
    socal
    Posts
    1,241

    Re: Part numbers and parts that fit the Consulier

    Yes feet, Im real curious what mph/ET Barbie will do with that conservatively improved 8v. I'm not bigtime enough to do say, a 500hp powerplant like SOME folks are.. :P
    MinivanRider

  12. #32
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    Is this the passenger or driver side axle that matches the caravan? or both sides? what year caravan?
    He didn't say, but I would think about the same years...1988-1994
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  13. #33
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    To get an axle for a Consulier (same as Caravan) that is quality:

    Automotive Drivetrain12533 S.W. Main St.
    Tigard Oregon 97223

    Guy is JR
    ph: 503-639-9476


    web site....
    http://www.automotive-drivetrain.com
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  14. #34
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    BRAKES!

    As you know the rear brakes are 1988 Fiero.
    I wanted better rear braking so was checking into pads that would grip a little better.
    Was told EBC made good ones. (A Fiero racing guy told me they love these)
    Checked with the company and they looked up the part number for the "yellow"
    ....it is DP4325R.

    Most places list the "green" but I was
    told the yellow grip better and the companies that sell EBC never list it.

    So am sharing what I found out.
    I ordered them, should have them in a few days.

    - - - Updated - - -

    I ordered them from
    AutoAccessoriesGarage.com
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  15. #35
    turbo addict
    Join Date
    Oct 2007
    Location
    Rockville, Md
    Posts
    3,520

    Part numbers and parts that fit the Consulier

    If you want to change your brakes over to Wilwood.

    If you change your rear spindles to std Daytona like the front you can call TCE performance in Arizona.

    They made custom caliper brackets and have them filed away in their shop if Consulier owner would ever want to replicate what I have.

    We know this caliper setup will clear my Enkie RFP1 16" wheels but not sure about your wheels.

    The whole setup including pads was just under $2400 shipped
    Last edited by 168glhs1986; 07-15-2014 at 09:51 PM.

  16. #36
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    If you need better rear brakes, I was told these work well.
    I will install them and let you know.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	yellowpads.JPG 
Views:	165 
Size:	386.5 KB 
ID:	51195  
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  17. #37
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    Drivers side drive axle is the same as a Caravan.
    BUT the passenger side is not.
    Its longer. They are not the same length.
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  18. #38
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    Heavier springs for the Consulier if interested.

    [TABLE="width: 600"][TR][TD="width: 10"][/TD][TD="width: 311, align: left"]QA1 Coil Springs
    HAL-9-450...450lb springs for the front


    [/TD][/TR][/TABLE][TABLE="width: 600"][TR][TD][/TD][TD="width: 311, align: left"]QA1 Coil Springs
    HAL-9-550...450lb springs for the rear
    [/TD][/TR][/TABLE]
    Or use the 450's for front and rear.
    Stock were 350 on all points I was told.

    - - - Updated - - -

    Adjustable coil-over shocks.

    [TABLE="width: 600"][TR][TD="width: 157, align: left"]HAL-DS401
    Coil-Over Shock, Proma Star, Twin-Tube, 14.000 in. Extended, 10.125 in. Collapsed,(Mfr. #: DS401)
    From summit.

    These work on the rear and should also fit the front.
    [/TD][TD="width: 10"][/TD][TD="width: 29, align: center"]2[/TD][/TR][/TABLE]
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  19. #39
    turbo addict
    Join Date
    Jan 2006
    Location
    Coos Bay, Oregon
    Posts
    5,439

    Re: Part numbers and parts that fit the Consulier

    added this:

    Power Brake Booster part #54-74100 ( this number good at most parts stores)
    Great stuff for great cars! Poly engine mounts and bushings at: http://www.polybushings.com

  20. #40
    Hybrid booster
    Join Date
    Jul 2006
    Location
    Gilbertsville, PA
    Posts
    529

    Re: Part numbers and parts that fit the Consulier

    Do we know what master cylinder we use with it? I'm guessing a 4wheel disc daytona?

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. TIII part numbers for the r/t
    By GLHX in forum 16v Factory Engines
    Replies: 11
    Last Post: 07-13-2011, 05:37 PM
  2. Need part numbers
    By prepared in forum Engine - Block, Piston, Heads, Intakes
    Replies: 7
    Last Post: 06-02-2010, 03:14 PM
  3. Anyone have the part numbers.....?
    By turbojerk in forum Suspension, Brakes, Wheels, Traction
    Replies: 0
    Last Post: 12-02-2009, 07:22 PM
  4. 1982-1996 MOPAR PARTS CATALOGS (Part Numbers/Illustrations)
    By martin kolner in forum The Original "Turbo Dodge" Cars
    Replies: 5
    Last Post: 04-23-2008, 07:18 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •