Spirit R/T front brakes are gone, still have the Daytona Shelby big brake front set.
Spirit R/T front brakes are gone, still have the Daytona Shelby big brake front set.
Working on clearing the decks.
Just some pictures from my road trip- I'll not have a chance to go through many things till after SDAC-25 but if you see something you need and its large contact me and I can bring it to SDAC-25 free of charge.
The GLHS was taken apart to be restored and then sat in a garage for years. It currently has a manual rack in it. I have the original motor and trans along with the intercooler. Louvers are there and in very good condition. The car is RUST FREE. I have the complete nose for the car. If interested as is drop me a line. After SDAC-25 were going to start reassembling and the price goes up. $1500 as it sits taken apart. Interior is decent too.
The 3" swingvalve is brand new as is the clutch disc, there is an aftermarket 89-90 CSX grill and one brand new headlamp, 87 CSX front bumper cover, spare GLHS nose, a VNT turbocharger (not broken) a few mitu's a few early turbo I and turbo II turbos, pumper rims, etc.
Working on clearing the decks.
Is that a MP 005 gasket? If so, I'll take it.
Is either one of those Shelby valve covers a 1 piece gasket?
Price on 3" swing valve? Might make a good fathers day gift
James Reeves - Reeves Racing
World's Fastest 8 Valve - 146.88 mph
86 GLH-T 9.99 at 143.78 mph
86 GLHS #169 Mom's - complete Super 60 car
87 Shelby Z 14.16 Dad's - mostly stock, no sh*t!
88 Shelby Z 13.5 - been in storage for 15 years
03 SRT-4 12.24 Mom's
07 Charger 5.7L 12.48 Dad's
Do you have any +20% injectors or 3bar MAP?
Yes I have both.Originally Posted by 19luis8510
Working on clearing the decks.
Fairly sure its an 006, no one piece valve covers and I'll be in touch James on the last part.Is that a MP 005 gasket? If so, I'll take it.
Is either one of those Shelby valve covers a 1 piece gasket?
Price on 3" swing valve? Might make a good fathers day gift
Working on clearing the decks.
PM sent
ZF pump , bracketry, or pulley?
I have a ZF setup off a 90 VNT Lebaron- Pump, brackets and pulley.
Working on clearing the decks.
Morning my brother, what do want for the zf set up u have,I'm definately interested. Regards Errol
Actually board member "twon1977" sent me a P.M. first and then "acannell" made a post here, I'd have to give "twon1977" first shot at it.
It is very possible I have a second pump in the garage attached to a rack I have to pull out of stores in the next week. But I'm fairly sure I don't have three. I was never a fan of the ZF pump and converted my '91 over to the ham can Saginaw style.
Working on clearing the decks.
Is that a small spline clutch disc? Is it just the disc?
Just a new disc, I'll have to check tonight if small spline or not. Pressure plate should be easy to obtain. I see kits you could rob the plate from on Rock Auto for $56
On the 3" swingvalve- It is brand new never used, $250 shipped in the US for anyone interested.
Working on clearing the decks.
no prob I was just looking on behalf on Twon1977.
1) Computer situation is really getting out of hand, I need to inventory the new arrivals. One is a 3 bar VNT that was reported to work well.
2) Ported 287 head, roughed out no finsh work. Bare head $50
3) Ported exhaust manifold with EGT $50
4) Turbo II intake with rail $140. Someone gasket matched so only good for large plenum mod as far as I'm concerned.
GLHS cluster, steering wheel and shifter knob.
One intercooler assembly is from Daytona which looks nice, the other is from a VNT car which looks rough.
$50 fair for the GLH air dams? They look nice. I can deliver to SDAC.
There is a convertable boot in really nice shape, almost looks new. Don't think its factory though.
Working on clearing the decks.
any of those turbos have a 2.5" swingvalve? also have any gtc lace style wheels to sell?
Hello,
I'm interested in :
- 3" swingvalve
- Ported exhaust manifold with EGT
- Turbo II intake with rail. Someone gasket matched so only good for large plenum mod.
Could this intake be used with a 655 head ?
Would work with any of the SOHC heads.
Working on clearing the decks.
No swingvalve for sale aside from the 3" but I do currently have a set of nice GTC wheels holding up the CSX while it is at the body shop. I have owned them since 2001.
Working on clearing the decks.
I wanted to know if the porting corresponds to the 655 ports : http://www.turbododge.com/forums/f4/...m-smaller.html
Posting Permissions
Reply With Quote
