Fix that CRX!
Fix that CRX!
Brent GREAT DEPRESSION RACING 1992 Duster 3.0T The Junkyard - MS II, OEM 10:1 -[I] Old - 11.5@125 22psi $90 [U]Stock[/U] 3.0 Junk Motor - 1 bar MAP [/I] 1994 Spirit 3.0T - 11.5@120 20 psi - Daily :eyebrows: Holset He351 -FT600 - 393whp 457ft/lb @18psi 1994 Spirit 3.0T a670 - He341, stock fuel, BEGI. Wife's into kid's project. 1990 Lebaron Coupe 2.2 TI/II non IC, a413 1990 Spirit 3.0 E.S. 41TE -- 1993 Spirit 3.0 E.S. 41TE -- 1994 Duster 3.0 A543 1981 Starlet KP61 Potential driver -- 1981 Starlet KP61 Parts -- 1983 Starlet KP61 Drag 2005 Durango Hemi Limited -- 1998 Dodge 12v 47re. AFC mods, No plate, Mack plug, Boost elbow -- 2011 Dodge 6.7 G56
Well i forgot about these for a while but here's a couple pics of the 4ch amp install.
Annnndddd.. with the carpet in place:
I ran the front speaker signals on the rear speaker wires and just jumped across the adapter harness so there is no alteration to the factory wiring other than where i clipped the pigtails from the rear speakers (it was already cut when i ran the aftermarket speakers off the head unit anyway). The dash speakers are T-tapped in parallel off the adapter harness as well so the front speakers are wired for 2-ohm. The back are 4. So the dash speakers are Infinity Reference 4" coax, the front door speakers are MB Quart 5.25" coax, and the rear deck speakers are MB Quart 6.5" components with the woofer mounted in the 6x9 deck holes with 1/4" mdf adapter plates.
I liked it so far but it's not quite there without the subs. The sub box will be a small sealed box for 2 12s in the spare tire well, with a hinged lid covering up the rest of the tire well where the amp will be and there will be a little bit of room for tools/jumpers/etc. Should be flush with the rest of the trunk on top. Not sure what i'll use for a sub amp yet but im reusing my old subs, 12" Infinity Kappa Perfect 4-ohm single voice coils.
Dont push the red button.You hear me?
Any updates on this? I'm actually putting together my parts list to put a turbo on my 2003 T&C AWD with 215hp 3.8L.
Interestengly I also settled on AEM fuel and spark box after getting a run-around from SCT, B&G and many others (including old friends).
I have so far accumulated a set of 42lbs injectors (but may go to ford injectors to match the new style fuel rail), walbro 255hp fuel pump setup for SRT, GN turbo, 65mm throttle body from 90's 4.7L, Innovate LC-1, a nice large intercooler and a set of exhaust manifolds to mod for turbo flange.
On order is the AEM box.
Keep up the good work, very interested in your results.
Alex...
Thanks Alex. I still haven't fixed the darn PS pump, but i DID swap in most of the 3" exhaust from the old car. It's 2.5" stock downpipe down to 3" cat and then 3" mandrel bent to behind the rear axle where it just ends right now. I think i want to try a dynomax VT muffler on it. I had a dynomax straight-through oval case SS-mesh packed muffler on the last car and the noise level was really good but the sound itself was pretty bad. Trying to get a more attractive tone this time around.
Dont push the red button.You hear me?
I've used magnaflow round resonator and a muffler on my minivan and it sounds pretty good. 2.5" mandrel bent. I've also used a Monza resonated tip to "upscale" the sound. It's actually pretty civilized but when I step on it sounds very nice, especially with the short ram intake I added recently. Exhaust and intake actually made a pretty big difference in passing power.
Here's a clip of my exhaust when it was just finished, it's deeper and louder now after it's got some miles on it.
http://www.flickr.com/photos/7310316@N03/4875624997
Alex...
Only news is that i found out i can get that PS pulley any day of the week for $12.. BUT i got talked into (wasnt hard..) slamming together my 88 Lancer Shelby for the GRM $2013 Challenge so now i have 5 more weeks of excuses to not work on this Dynasty..
Dont push the red button.You hear me?
Ha, ha! Well, that's a good excuse to have.
Good luck, I'll keep an eye out for your entry.
Alex...
In case someone is stumbling upon this, this late in life;
the different 4-bolt pattern & bolt size for the rear axle mentioned in the OP, is identical to the PT Cruiser and rear caliper brackets/backing plates, brakes, spindles & hub bearings can all be swapped from a PT to a Dynasty/New Yorker/Imperial (C & Y bodies).
ive got a write up on it over at the other place.
just FYI