Results 1 to 10 of 10

Thread: The Tool Shed went out again.

  1. #1
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    The Tool Shed went out again.

    Much better tonight, got 6 runs in, last week, only 3, I could have run 2 more but read on and see why.

    Got there, rushed around, got the race fuel in and had time to rip to the staging lanes, I was the last one, ran a 14.0@98 mph, race fuel didn't have time to mix and it was FAT, 25 psi, 2.1 60ft.

    Take out some fuel, and off I go, rip off a 13.9@98.80 mph and a 2.2 60ft. Track isn't sticky tonight, still rich.

    Take out some fuel and back I go, 13.7@99.46 mph, 2.1 60ft and now she's lean, grrrrrrrrr.

    Add some more fuel and add a rock to my MBC to bump up the boost, stage and something doesn't feel right, it barely did a burn out. Launch and its gutless, look at my boost guage, 8 psi, , run a screaming 16.5@78 mph.

    Go back and fix it, so I thought, another screamer, literally same time.

    Go back and remove rock, stretch spring and go back, run and she's pulling, don't notice how much boost but she pings then a pop, look at the boost, oops, 35 psi. Ended up blowing the head gasket at #1 cylinder.

    Guess its time to rering and get rid of the Total Seal rings and get a Super50 compressor wheel, I NEED to get the alky system working, the mixing of race fuel and pump gas is holding me back.

    Time is running out to run 12's, don't think I am going to do it this year,
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  2. #2
    Garrett booster
    Join Date
    Mar 2006
    Location
    INDIANA!!! Muncie area
    Posts
    243

    Re: The Tool Shed went out again.

    Hey at least you didn't crack your head......

    If your boost controller needs a new spring, check out www.voodooboost.com - You can get rebuild kits for them with a new spring and ball. Most of their boost controllers guarantee you can run 30+psi, but one of the kits has a 10-50psi spring. No more rock in the boost controller! Sometimes they list stuff on ebay cheaper too.

  3. #3
    boostaholic
    Join Date
    Dec 2005
    Location
    Columbus Ohio
    Posts
    1,166

    Re: The Tool Shed went out again.

    sorry about your luck simon Im glad to hear nothing Major went wrong

  4. #4
    Hybrid booster
    Join Date
    Jan 2006
    Location
    Ohio
    Posts
    737

    Re: The Tool Shed went out again.

    Simon,
    Sorry for your bad luck at the track, seems to be turbo mopar curse.

    Fixed my problem , go to the track, 2nd run my main brass elbow for the vacuum block breaks off

    We'll achieve our goals eventually.

  5. #5
    turbo addict boost geek's Avatar
    Join Date
    Dec 2005
    Location
    Chilliwack, B.C.
    Posts
    2,290

    Re: The Tool Shed went out again.

    99.4 mph! 35 psi and only blew the h.g! Wow! Did you drive home? I drove to Chilliwack from Mission with a blown h.g., but what a trail of smoke I left behind, had to stop and add water a couple times. If your almost at 100 mph, 12 are very close, just hook up and your there!!!
    If you upgrade your turbo, remember little ol' me!
    later Dick Westerhof

  6. #6
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: The Tool Shed went out again.

    I bought an electric boost controller off Ebay, tired of playing with the MBC, now I can control it from the ----pit. It probably wont' get here in time for any runs.

    I wouldn't say its bad luck, just me being super aggressive, lol!

    Dick, I had it towed to my shop, guess its time to invest in BCAA. Water was pouring in soo fast, I wouldn't have made it, shop is 40 mins away.
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  7. #7
    Hybrid booster
    Join Date
    Jan 2006
    Location
    United States
    Posts
    601

    Re: The Tool Shed went out again.

    Congrats simon, Don't give up, seems like you and I are the only 2 racing minivans this year. I have a little story to tell of my own about my runs last night.

  8. #8
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: The Tool Shed went out again.

    PM me, spill your guts,
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  9. #9
    Hybrid booster
    Join Date
    Jan 2006
    Location
    United States
    Posts
    601

    Re: The Tool Shed went out again.

    posted it already haha

  10. #10
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: The Tool Shed went out again.

    Quote Originally Posted by Ubmbass
    posted it already haha

    Saw and posted!
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

Similar Threads

  1. The Tool Shed goes faster.
    By turbovanmanČ in forum Strip & Street Stories
    Replies: 32
    Last Post: 08-27-2006, 05:00 PM
  2. The Flying Tool Shed wasn't flying, its sucked a*s!
    By turbovanmanČ in forum Strip & Street Stories
    Replies: 33
    Last Post: 08-21-2006, 12:35 PM
  3. Lebaron GTC, Flying Tool Shed - Friday at Mission Raceway
    By Whorse in forum Strip & Street Stories
    Replies: 17
    Last Post: 05-25-2006, 09:53 PM
  4. The Tool Shed goes even faster, 13.6@98 mph but Oops, I did it again, :(
    By turbovanmanČ in forum Strip & Street Stories
    Replies: 15
    Last Post: 05-24-2006, 08:53 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •