Results 1 to 7 of 7

Thread: 1sg gen Neon rear struts and springs, PITA?

  1. #1
    turbo addict
    Join Date
    Jul 2007
    Location
    Niagara Falls, ON
    Posts
    7,548

    Question 1sg gen Neon rear struts and springs, PITA?

    Hi guys,

    So the rear struts on my SIL's 1st gen Neon seem to be completely shot. She really doesn't want to put much money into it at all, because we don't think it's got more than another year or two due to corrosion issues, and the electrics are getting a bit funky also.

    Anyway, options seem to be, wreckers yard assemblies which don't seem all that well priced for any that are local, around $75 a side and they might not last the year or two. Cheapy new assemblies seem to be in the $120 range. Cheapy struts by themselves seem to run at about $30 or $40 though.

    I've got some of those spring clamps, and I've done front struts before with those, and a lot of safety chain, but they need a bit of clearance to use on the car, which I usually like to do, to get better compression with the weight on the springs.

    So wondering how much of a PITA it is to swap struts without springs on the rear, and whether to volunteer my services or not.... coz I figure she can get shop to stick the cheapies on for about the same as the assemblies.

    thanks,


    RW222
    DD1: '02 T&C Ltd, 3.8 AWD. DD2: '15 Versa Note SV, replacing.. DDx: '14 Versa Note SV << freshly killded :( ....... Projects: '88 Voyager 3.0, Auto with shift kit, timing advance, walker sound FX muffler on 15" pumpers wrapped in 215/65/R15 H rated Nexens.... and a '95 phord escort wagon PnP head << Both may need to go :( ..... I like 3.0s ... so??? ... stop looking at me like I've got two heads!

  2. #2
    Rhymes with tortoise. Turbo Mopar Staff cordes's Avatar
    Join Date
    Dec 2005
    Location
    Tuscola, IL
    Posts
    21,441

    Re: 1sg gen Neon rear struts and springs, PITA?

    IIRC the springs didn't need to be compressed enough to necessitate a spring compressor when I did the rears on ours. I could push them down enough by hand to use a gun to remove the nut. Installation was a little more complicated, but nothing to complain about.

  3. #3
    See me ride out of the sunset... Turbo Mopar Staff BadAssPerformance's Avatar
    Join Date
    Dec 2005
    Location
    Chicagoland!
    Posts
    27,688

    Re: 1sg gen Neon rear struts and springs, PITA?

    Chryguy was mentioning the redi-struts that come with new springs and mounts ready to go... sounded like a 30min job with those.

    JT
    SDAC Director
    SDAC-Chicago President
    JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
    87 Shelby Z - 10.50@141.66mph
    87 CSX #751 Clone - 12.88@102.88mph

    www.badassperformance.com
    Check out Turbo-Mopar Times!
    Submit your 1/4 mile times HERE!!

    Support SDAC! Join Today!
    "I'm not some pro athlete with a bajillion dollars, I'm just an every man"
    Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.

  4. #4
    Rhymes with tortoise. Turbo Mopar Staff cordes's Avatar
    Join Date
    Dec 2005
    Location
    Tuscola, IL
    Posts
    21,441

    Re: 1sg gen Neon rear struts and springs, PITA?

    Quote Originally Posted by BadAssPerformance View Post
    Chryguy was mentioning the redi-struts that come with new springs and mounts ready to go... sounded like a 30min job with those.
    That's really easy. Just the three nuts in the trunk and the two holding the strut in. There is the one holding the brake line on their too I guess.

  5. #5
    turbo addict
    Join Date
    Dec 2005
    Location
    Pickering, ontario
    Posts
    2,670

    Re: 1sg gen Neon rear struts and springs, PITA?

    ^^ Best option in my opinion. The strut mounts very likely need to be replaced as well as the struts. This way you get it as am assembly. The only down side is, many of the new struts have an elongated lower hole (hehehe) and require you mark the rear knuckle before you remove them so you don;t ruin the rear alignment.

  6. #6
    Super Moderator Turbo Mopar Staff contraption22's Avatar
    Join Date
    Dec 2005
    Location
    Havertown, PA
    Posts
    9,517

    Re: 1sg gen Neon rear struts and springs, PITA?

    The other downside is these "Quick Struts" also usually have a one-size-fits-all coil spring for a given YMME. While there might be 4 or 5 different spring rates from the factory.
    Mike Marra
    1986 Plymouth Horizon GLMF "The Contraption" < entertaining sponsorship offers
    Project Log:
    http://www.turbo-mopar.com/forums/showthread.php?69708-The-Contraption-2013-14&highlight=

  7. #7
    turbo addict
    Join Date
    Jul 2007
    Location
    Niagara Falls, ON
    Posts
    7,548

    Re: 1sg gen Neon rear struts and springs, PITA?

    Well I just went with the "economy" quick struts from my local parts guys, think they were branded Cardinal, but then they had Monroe stickers on the box and surprise "Made in USA".

    They did have that elongated top hole in the knuckle clamp. I scribed the knuckle, but for reference, the bolt positioned toward the back of the hole with about 1/8" remaining.

    Springs and mounts didn't look too bad when they came off, so I put 'em up for grabs locally on OSDAC, in case anyone needs those or the whole caboodle for a "pattern" or to carve up for the bits and pieces to adapt eBay cheapies.

    Rides a helluva lot better. No apparent alignment issues thus far.

    Dumb thing had a groaning noise though, hard to pinpoint you seem to hear it through the whole of the bodywork, well that seemed to me to have got louder, but my SiL said it was louder before... anyway was wondering if it was the rear bearings, transmitting more noise now that the struts are stiff. However, couldn't feel play in them and they're not getting hot.
    DD1: '02 T&C Ltd, 3.8 AWD. DD2: '15 Versa Note SV, replacing.. DDx: '14 Versa Note SV << freshly killded :( ....... Projects: '88 Voyager 3.0, Auto with shift kit, timing advance, walker sound FX muffler on 15" pumpers wrapped in 215/65/R15 H rated Nexens.... and a '95 phord escort wagon PnP head << Both may need to go :( ..... I like 3.0s ... so??? ... stop looking at me like I've got two heads!

Similar Threads

  1. 1st gen Neon rear sway bars?
    By cordes in forum Other vehicles
    Replies: 24
    Last Post: 08-25-2010, 12:39 AM
  2. General struts and hood springs?
    By t2shadow in forum Parts Wanted
    Replies: 0
    Last Post: 07-02-2010, 08:55 AM
  3. 1st Gen Neon wobbly rear struts/shocks.
    By RoadWarrior222 in forum Other vehicles
    Replies: 2
    Last Post: 08-29-2009, 10:38 PM
  4. 89 mini struts/ springs
    By Mr overkill in forum Suspension, Brakes, Wheels, Traction
    Replies: 3
    Last Post: 05-20-2009, 12:19 PM
  5. General 1st Gen Neon stuff-ABS, header, lowering springs, strut bar, sway bars.
    By turbovanmanČ in forum Parts For Sale
    Replies: 0
    Last Post: 03-14-2009, 06:46 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •