Page 1 of 2 12 LastLast
Results 1 to 20 of 28

Thread: sealant on headgasket?

  1. #1

    sealant on headgasket?

    Is it good or bad to use copper spray sealant on your headgasket?
    Thanks,
    Frank

  2. #2
    turbo addict
    Join Date
    Dec 2005
    Location
    Pickering, ontario
    Posts
    2,670

    Re: sealant on headgasket?

    It's not a recommended procedure from the manufacturer, but I wouldn't be surprised to hear some people say it's a great thing to make up for small variences in gasket surfaces.

  3. #3

    Re: sealant on headgasket?

    Would using it cause a problem?

  4. #4
    two point two much fun Turbo Mopar Staff Turbodave's Avatar
    Join Date
    Dec 2005
    Location
    Northern IL
    Posts
    4,832

    Re: sealant on headgasket?

    I've used it many times on the MP gaskets and have had no issues, I like to think it helps get a good seal and transfer heat across the gasket.
    Dave Tekampe
    Director SDAC National
    VP SDAC-Chicago


    85 GLH-Turbo (DC intercooled)
    86 GLHS #107
    87 GLHS #148
    87 CSX #161, #608, #674
    88 CSX-T #529, #541
    89 Shadow Competition Package and lots more...

  5. #5

    Re: sealant on headgasket?

    Thanks. I guess I'll use it then.

  6. #6
    turbo addict
    Join Date
    Dec 2005
    Location
    Pickering, ontario
    Posts
    2,670

    Re: sealant on headgasket?

    Quote Originally Posted by Turbodave View Post
    I've used it many times on the MP gaskets and have had no issues, I like to think it helps get a good seal and transfer heat across the gasket.
    Do you run any non-coated gaskets in your cars?

  7. #7
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: sealant on headgasket?

    I run it if its an older engine but if both surfaces are fresh, then I don't bother. It won't hurt so if your a bit worried about seal, just use it.
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  8. #8
    See me ride out of the sunset... Turbo Mopar Staff BadAssPerformance's Avatar
    Join Date
    Dec 2005
    Location
    Chicagoland!
    Posts
    27,688

    Re: sealant on headgasket?

    Head Gasket in a can!


    JT
    SDAC Director
    SDAC-Chicago President
    JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
    87 Shelby Z - 10.50@141.66mph
    87 CSX #751 Clone - 12.88@102.88mph

    www.badassperformance.com
    Check out Turbo-Mopar Times!
    Submit your 1/4 mile times HERE!!

    Support SDAC! Join Today!
    "I'm not some pro athlete with a bajillion dollars, I'm just an every man"
    Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.

  9. #9
    turbo addict
    Join Date
    Dec 2005
    Location
    Lincoln, Nebraska
    Posts
    2,626

    Re: sealant on headgasket?

    I use the Mopar gasket spray intended for thier MLS headgaskets on the headgaskets I install. I've never had one leak using that stuff.

  10. #10
    Moderator Turbo Mopar Staff Vigo's Avatar
    Join Date
    Feb 2006
    Location
    San Antonio,TX
    Posts
    10,798

    Re: sealant on headgasket?

    I sprayed some on two used (not for long) MP headgaskets, both held 18psi without problems. About to copper spray and reuse another one, in fact..

    Dont push the red button.You hear me?

  11. #11
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: sealant on headgasket?

    Quote Originally Posted by 86Shelby View Post
    I use the Mopar gasket spray intended for thier MLS headgaskets on the headgaskets I install. I've never had one leak using that stuff.
    Got a part number?
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  12. #12
    turbo addict
    Join Date
    Dec 2005
    Location
    Lincoln, Nebraska
    Posts
    2,626

    Re: sealant on headgasket?

    Going by the description I found online this should be it. I'm not close enough to the garage to be able to double check.

    4318035AA

    http://roeracing.com/ProductCart/pc/...idcategory=243

  13. #13
    turbo addict
    Join Date
    Feb 2010
    Location
    Piedmont, Ohio
    Posts
    4,109

    Re: sealant on headgasket?

    HYLOMAR! It fills all the little imperfections in the head and block. It also works great on paper gaskets because they wont stick and you can re use them
    Ian Adams Function>Form 1990 shadow scrapped, too rusty:( 1991 Spirit R/T Scrapped, parts sold:( 1989 Turbo Caravan Daily beater with built-[I]ish [/I]​engine slowly evolving into weekend turbo beater.

  14. #14
    turbo addict Turbo Mopar Contributor
    Join Date
    Dec 2005
    Location
    Seattle
    Posts
    7,063

    Re: sealant on headgasket?

    Used copper spray on a 100k mile set of headgaskets that sat in a shed for 3 years. Got them to seal after warming up the engine (and not retorquing anything). Only problem was 1 coolant passage that leaked until it warmed up.

    Hylomar is good stuff but its very expensive. Use it for solid copper headgaskets. Thats how you get copper headgaskets to seal longterm. Copper is the only time I would use it but its probably better for doing stupid stuff like paper gaskets that have serious mileage on them. More expensive then the headgasket being replaced so it would not make sense to actually do it.

    I am going to reuse a set of paper gaskets next month, but they were new Felpro as of last year. Swapping heads between cars.
    Then the motor that had those gaskets gets a new set someday when I put it back together. I use it on new gaskets, paper and MLS. Mostly because I would rather spray then remove material from my cylinder head (weak deck). The real reason is money, the other things are justifications
    Brent GREAT DEPRESSION RACING 1992 Duster 3.0T The Junkyard - MS II, OEM 10:1 -[I] Old - 11.5@125 22psi $90 [U]Stock[/U] 3.0 Junk Motor - 1 bar MAP [/I] 1994 Spirit 3.0T - 11.5@120 20 psi - Daily :eyebrows: Holset He351 -FT600 - 393whp 457ft/lb @18psi 1994 Spirit 3.0T a670 - He341, stock fuel, BEGI. Wife's into kid's project. 1990 Lebaron Coupe 2.2 TI/II non IC, a413 1990 Spirit 3.0 E.S. 41TE -- 1993 Spirit 3.0 E.S. 41TE -- 1994 Duster 3.0 A543 1981 Starlet KP61 Potential driver -- 1981 Starlet KP61 Parts -- 1983 Starlet KP61 Drag 2005 Durango Hemi Limited -- 1998 Dodge 12v 47re. AFC mods, No plate, Mack plug, Boost elbow -- 2011 Dodge 6.7 G56

  15. #15
    See me ride out of the sunset... Turbo Mopar Staff BadAssPerformance's Avatar
    Join Date
    Dec 2005
    Location
    Chicagoland!
    Posts
    27,688

    Re: sealant on headgasket?

    Quote Originally Posted by 86Shelby View Post
    I use the Mopar gasket spray intended for thier MLS headgaskets on the headgaskets I install. I've never had one leak using that stuff.
    Good point on using the Mopar stuff on the Mopar MLS gaskets

    As a side note, Cometics does NOT recomend spraying their MLS headgaskets with anything as they are already Viton™ coated already... I didnt ask them if they need to be sprayed if re-used tho?

    JT
    SDAC Director
    SDAC-Chicago President
    JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
    87 Shelby Z - 10.50@141.66mph
    87 CSX #751 Clone - 12.88@102.88mph

    www.badassperformance.com
    Check out Turbo-Mopar Times!
    Submit your 1/4 mile times HERE!!

    Support SDAC! Join Today!
    "I'm not some pro athlete with a bajillion dollars, I'm just an every man"
    Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.

  16. #16
    turbo addict Turbo Mopar Contributor
    Join Date
    Dec 2005
    Location
    Seattle
    Posts
    7,063

    Re: sealant on headgasket?

    Cometics are terrible headgaskets anyways. They somehow manage to make a worse MLS then OEM MLS.
    Brent GREAT DEPRESSION RACING 1992 Duster 3.0T The Junkyard - MS II, OEM 10:1 -[I] Old - 11.5@125 22psi $90 [U]Stock[/U] 3.0 Junk Motor - 1 bar MAP [/I] 1994 Spirit 3.0T - 11.5@120 20 psi - Daily :eyebrows: Holset He351 -FT600 - 393whp 457ft/lb @18psi 1994 Spirit 3.0T a670 - He341, stock fuel, BEGI. Wife's into kid's project. 1990 Lebaron Coupe 2.2 TI/II non IC, a413 1990 Spirit 3.0 E.S. 41TE -- 1993 Spirit 3.0 E.S. 41TE -- 1994 Duster 3.0 A543 1981 Starlet KP61 Potential driver -- 1981 Starlet KP61 Parts -- 1983 Starlet KP61 Drag 2005 Durango Hemi Limited -- 1998 Dodge 12v 47re. AFC mods, No plate, Mack plug, Boost elbow -- 2011 Dodge 6.7 G56

  17. #17
    turbo addict
    Join Date
    Dec 2005
    Location
    Mesa, AZ
    Posts
    7,351

    Re: sealant on headgasket?

    Installed 4 MP headgasket dry into different cars, never had a problem with leaking.

  18. #18
    See me ride out of the sunset... Turbo Mopar Staff BadAssPerformance's Avatar
    Join Date
    Dec 2005
    Location
    Chicagoland!
    Posts
    27,688

    Re: sealant on headgasket?

    Quote Originally Posted by Ondonti View Post
    Cometics are terrible headgaskets anyways. They somehow manage to make a worse MLS then OEM MLS.
    I have had great luck with them on both the 2.2L and 2.4L

    What problems have you had on yoru car with them? Why do you think they are terrible?

    JT
    SDAC Director
    SDAC-Chicago President
    JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
    87 Shelby Z - 10.50@141.66mph
    87 CSX #751 Clone - 12.88@102.88mph

    www.badassperformance.com
    Check out Turbo-Mopar Times!
    Submit your 1/4 mile times HERE!!

    Support SDAC! Join Today!
    "I'm not some pro athlete with a bajillion dollars, I'm just an every man"
    Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.

  19. #19
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: sealant on headgasket?

    Quote Originally Posted by BadAssPerformance View Post
    I have had great luck with them on both the 2.2L and 2.4L

    What problems have you had on yoru car with them? Why do you think they are terrible?
    I had a used one not seal under boost, coated it too,
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  20. #20
    See me ride out of the sunset... Turbo Mopar Staff BadAssPerformance's Avatar
    Join Date
    Dec 2005
    Location
    Chicagoland!
    Posts
    27,688

    Re: sealant on headgasket?

    All bets are off on any "used" gasket

    But now I'm curious, did you coat it between the layers?

    JT
    SDAC Director
    SDAC-Chicago President
    JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
    87 Shelby Z - 10.50@141.66mph
    87 CSX #751 Clone - 12.88@102.88mph

    www.badassperformance.com
    Check out Turbo-Mopar Times!
    Submit your 1/4 mile times HERE!!

    Support SDAC! Join Today!
    "I'm not some pro athlete with a bajillion dollars, I'm just an every man"
    Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.

Page 1 of 2 12 LastLast

Similar Threads

  1. Thread sealant?
    By chad_m in forum "I need help!"
    Replies: 11
    Last Post: 01-20-2010, 01:59 PM
  2. intake sealant?
    By W.P._Turbocars in forum 3.0L V6 Turbo Engines!
    Replies: 15
    Last Post: 06-19-2009, 12:39 PM
  3. Anaerobic Sealant Vs Loctite 680
    By 89ShelbyGuy in forum Engine - Block, Piston, Heads, Intakes
    Replies: 4
    Last Post: 06-17-2009, 11:24 PM
  4. Adhesive / Sealant?
    By shelbydave in forum Interior & Exterior Restoration
    Replies: 2
    Last Post: 04-03-2009, 03:04 PM
  5. Any alternative to anaerobic sealant?
    By WickedShelby88 in forum Engine - Block, Piston, Heads, Intakes
    Replies: 2
    Last Post: 06-24-2008, 01:33 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •