10 an fuel rails

[risen]

I have 2 10an size fuel rails that I'm looking to sell. I drilled the injector ports with a tool specifically made for cutting the injector ports on a drill press. The rest of the rail hasn't been touched. The spacing between the ports is for a t1/t2 IDK if they'll work for a t3 or 16v head. The inlet/outlet ends aren't tapped out yet and the inside can use a good cleaning. I'm selling them as-is for 45$ ea. PM me if you're interested.

If there's overwhelming demand I can make more.

[GLHNSLHT2]

The spacing for a Masi head is the same as the T1/T2 spacing. I'd assume the T3 is the same.

[thefitisgay]

so they are aluminum?

[risen]

The spacing for a Masi head is the same as the T1/T2 spacing. I'd assume the T3 is the same.

Good to know, thanks.

so they are aluminum?

Yes, 6063.

[minigts]

I thought the T3 rails worked for the 2 piece intakes? Seems they are the same and knowing Chrysler they are too cheap to make something new.

[risen]

I thought the T3 rails worked for the 2 piece intakes? Seems they are the same and knowing Chrysler they are too cheap to make something new.

That may be. I don't have a T3 so I don't really know either way. But if enough of you have tried it, then I guess it'll work.

[zin]

10an?!! Good God Man! You could run nitro with stuff that big!

I'll always maintain that you practically can't go too big on your fuel system or ignition... Better to have it and not need it, than need it and not have it!!

Mike

PS Still... That's pretty damn big!

[minigts]

...
I'll always maintain that you practically can't go too big on your fuel system or ignition... Better to have it and not need it, than need it and not have it!!

...

Zin you need to change your name to Zen. You'r very philosophical. You remind me of The Sphinx from Mystery Men.

[zin]

Zin you need to change your name to Zen. You'r very philosophical. You remind me of The Sphinx from Mystery Men.

I love that movie! I'll take that as a high complement! I just hope the advice I dole out is as well received!

Mike

[turbovanman²]

I thought the T3 rails worked for the 2 piece intakes? Seems they are the same and knowing Chrysler they are too cheap to make something new.

Nope, different again, they face the other way so the outlets are swapped.

[risen]

10an?!! Good God Man! You could run nitro with stuff that big!

I'll always maintain that you practically can't go too big on your fuel system or ignition... Better to have it and not need it, than need it and not have it!!

Mike

PS Still... That's pretty damn big!

I say go big or go home . My thought on getting that rail was 2 fold: the larger volume will probably help remove fluctuations in pressure caused by the injectors and I'd never outgrow it.

[risen]

Both rails are sold to folks in the great white north. Thanks, guys!

I may be back with more in the future, since this went so well.

[OmniLuvr]

i hope so, it wasnt in the cards for me now, but deff later. these would probably make good rails for e-85 use...

[risen]

i hope so, it wasnt in the cards for me now, but deff later. these would probably make good rails for e-85 use...

Just hit me up with a PM when you're ready. I need to order more stock soon anyways, my brother's upset that I cut holes in his straight edge .

[Juggy]

nice rail. im super tempted!!!

aluminum is prey to E85 I dont think I would recommend anything other then SS

[zin]

nice rail. im super tempted!!!

aluminum is prey to E85 I dont think I would recommend anything other then SS

SS would be the best choice, but, if the rail were to be HARD anodized, it should be fine, just don't scratch through the anodizing!

Mike

[BadAssPerformance]

Both rails are sold to folks in the great white north. Thanks, guys!

I may be back with more in the future, since this went so well.

Nice rails man. Got a pic next to a T-II rail to see how long it is, the ends look a tad short?

If you do another batch, please post it up in the "Group Buy" section

[risen]

Nice rails man. Got a pic next to a T-II rail to see how long it is, the ends look a tad short?

I measured them to match the length of a early t1 rail. I forgot to put them up next to a ruler and take a pic, and I can't do it now since they're in the mail. Maybe Simon will be kind enough to post the real length when gets them. I think they're around 16 or 18 inches.

If you do another batch, please post it up in the "Group Buy" section

Will do.

[turbovanman²]

I measured them to match the length of a early t1 rail. I forgot to put them up next to a ruler and take a pic, and I can't do it now since they're in the mail. Maybe Simon will be kind enough to post the real length when gets them. I think they're around 16 or 18 inches.

Sure, no problem.

[BadAssPerformance]

Cool