Page 106. If using CM they only need to be 1 1/4" x .058. If you already have a MS bar then I don't know about rules on mixing materials. I would think it would be fine.
http://www.mydigitalpublication.com/...on/?m=1203&l=1
Page 106. If using CM they only need to be 1 1/4" x .058. If you already have a MS bar then I don't know about rules on mixing materials. I would think it would be fine.
http://www.mydigitalpublication.com/...on/?m=1203&l=1
Anybody know how much the rear quarter glass windows weigh on a G body?
best 1/8 ET-6.16 sec. best 1/8 speed-119.70 Best 1/4 MPH 145.5, Best 1/4 ET 9.65 sec. 8 valve NO NITROUS!!
I have a few sets laying around and if I had to guess probably about 5# per side or so. They aren't all that bad, but if you're going for ultimate lightness, then I say "why not"!? LOL They aren't structural and come out pretty darn easy once you get to the nuts on the back side.
Robert Mclellan
http://www.youtube.com/watch?v=wambNdfnu5M
10.04 @ 143.28mph (144.82 highest mph)
Worlds fastest 8v MTX Shelby Charger
Manitoba's Fastest 4cyl!
8 valve, No Nitrous!
New clutch combo is the SH!T!
Really!? they are bolted in? that would be great, I havent removed the trim to take a look. I thought they would be urathaned (glued) in like the hatch glass.
---------- Post added at 08:57 AM ---------- Previous post was at 08:56 AM ----------
Thanks Rob, would be appreciated.
best 1/8 ET-6.16 sec. best 1/8 speed-119.70 Best 1/4 MPH 145.5, Best 1/4 ET 9.65 sec. 8 valve NO NITROUS!!
I got this done so far, I'm now working on a functional rear wing, sorta like a pro stock style only smaller.
So far a 40lbs. weight removal. Was going to buy a glass hatch frame but it wouldnt support the wing without major reinforcements.
best 1/8 ET-6.16 sec. best 1/8 speed-119.70 Best 1/4 MPH 145.5, Best 1/4 ET 9.65 sec. 8 valve NO NITROUS!!
Is that 40lbs. solely from the holes in the hatch, or is that from the glass too? What was the weight of each?
Hatch looks very slick! How much weight came out with just the hole saw?
The rear 1/4 glass is held in with butyl (+ speed nuts), or at least it should be. If I have one that hasn't had the butyl cleaned off yet I'll weigh it to try and get the most accurate #'s.
Robert Mclellan
http://www.youtube.com/watch?v=wambNdfnu5M
10.04 @ 143.28mph (144.82 highest mph)
Worlds fastest 8v MTX Shelby Charger
Manitoba's Fastest 4cyl!
8 valve, No Nitrous!
New clutch combo is the SH!T!
Ok, The complete hatch with glass, trim,wing, and hinges weighed 81lbs. I took off 3lbs with the hole saw,got 1.5lbs. off by sculpting the hinges,the rubber weather seal weighed 3lbs., latch and key assbly-2.5lbs, factory glass weighes 26lbs.,lexan replacement weighs 10lbs., the original wing alone weighs 13lbs.
The complete hatch as you see in the pics now weighs 35lbs.
Removing weight is alot of work!, and not cheap. Total weight reduction came to 40lbs.
best 1/8 ET-6.16 sec. best 1/8 speed-119.70 Best 1/4 MPH 145.5, Best 1/4 ET 9.65 sec. 8 valve NO NITROUS!!
I can't believe you didn't use black hardware.
Wow, that was a lot of work with the hole saw for 3lbs. Worth it in the end though.
best 1/8 ET-6.16 sec. best 1/8 speed-119.70 Best 1/4 MPH 145.5, Best 1/4 ET 9.65 sec. 8 valve NO NITROUS!!
LOL, I'm just messing with you. I wish I had the time and patience to do something even 1/2 as clean as your car.
James Reeves - Reeves Racing
World's Fastest 8 Valve - 146.88 mph
86 GLH-T 9.99 at 143.78 mph
86 GLHS #169 Mom's - complete Super 60 car
87 Shelby Z 14.16 Dad's - mostly stock, no sh*t!
88 Shelby Z 13.5 - been in storage for 15 years
03 SRT-4 12.24 Mom's
07 Charger 5.7L 12.48 Dad's
Robert Mclellan
http://www.youtube.com/watch?v=wambNdfnu5M
10.04 @ 143.28mph (144.82 highest mph)
Worlds fastest 8v MTX Shelby Charger
Manitoba's Fastest 4cyl!
8 valve, No Nitrous!
New clutch combo is the SH!T!
That 40lb removal from the hatch will make a huge improvement in traction. More of a gain from better traction than from weight loss!! I removed close to the same amount of weight from the hatch of my GLHS and I could pull 1.9 60's on a regular basis running 300 treadwear tires!!!
Ok, very good, I can remove another 6.15lbs, I'm going for it.
And your saying I shouldnt have to cut them out?is that right?..........and thanks for weighing them Rob
---------- Post added at 10:15 AM ---------- Previous post was at 10:14 AM ----------
Goody!!!
best 1/8 ET-6.16 sec. best 1/8 speed-119.70 Best 1/4 MPH 145.5, Best 1/4 ET 9.65 sec. 8 valve NO NITROUS!!
Wish it was that easy for me to lighten my 1/4 appliques! They're prob just as heavy. Maybe a chance for me to try my luck at carbon fiber on something small......
You may have to/want to cut the butyl with a bannana knife, but it's butyl, so if you push evenly and it's warm enough, they Should just push out. (messy though) and your welcome.
Robert Mclellan
http://www.youtube.com/watch?v=wambNdfnu5M
10.04 @ 143.28mph (144.82 highest mph)
Worlds fastest 8v MTX Shelby Charger
Manitoba's Fastest 4cyl!
8 valve, No Nitrous!
New clutch combo is the SH!T!
1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
2004 GSW TDI, 5 speed, fully loaded, modified.
Aurora ignition wires for sale. Link to info
Super60 roller cams or custom/billet cams. Link to info
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.