does mptune work for you? i would like you to post up the mptune "mpt2coms.txt" file. it has a little more com port info in it that might be helpful.
does mptune work for you? i would like you to post up the mptune "mpt2coms.txt" file. it has a little more com port info in it that might be helpful.
89 Voyager LE, 2.5T2 - rest in peace
87 Charger Shelby T2 (2.4 conversion in process)
Mptune works fine. Here is mpt2coms.txt
-Comport analysis for mptune version 2.0.4.2
-Locating ports on computer-
name:USB Serial Port (COM3) deviceid:FTDIBUS\VID_0403+PID_6001+BBXNEO3PA\0000
number of ftdi devices found - 1
ftdi port num:COM3 serial num:BBXNEO3P
Inverted tx:True Inverted rx:True
Latency is set to:16
checking to see if usb port number COM3 is a moates device
Moates device not located on this port
default com port set to:COM3
Is there a list somewhere of each ram location with a better description of what they are? the short names listed in MPSCAN don't help a noob like me.
Thanks.
fwiw - the last update to mpscan included a file that can be displayed that shows the ram locations and a "long" description. for right now, none of the long descriptions have been set up. either you can do it yourself or wait until rob L has an opportunity to update the file.
89 Voyager LE, 2.5T2 - rest in peace
87 Charger Shelby T2 (2.4 conversion in process)
Yay for long descriptions, lol
Btw, I'd assume I have a bad SMEC, but I figured I'd check with you guys to be sure.
MPScan works great on my 89 LeBaron, but my brother's 88, it says something to the effect of "No valid ports, try turning the key off and back on"
Obviously I tried turning the key off and on a few times. Swapped both of my spare SMECs into the car and MPScan reads them just fine.
Thoughts?
Same PC and cable?
Hi wanted to introduce myself here, name is Nick. So I purchased everything i need from Boosted button to be able to log everything my car is doing and considering the build that Shadow is putting together for me. i'd really like to be able to log everything properly.
This is what I have so far and I am trying to find the knock sensor so that I can add it to a digital gauge and I cant seem to figure out how to increase the psi from 15 to 30 psi. I'd appreciate some help.
if you have a 3 bar map you should select the "map3bar" gauge. the knock volts is gauge "knkv".
89 Voyager LE, 2.5T2 - rest in peace
87 Charger Shelby T2 (2.4 conversion in process)
you need to update the layout reference files. go to settings / layout files / update settings, check all five boxes, click on the download button. now it should show up.
89 Voyager LE, 2.5T2 - rest in peace
87 Charger Shelby T2 (2.4 conversion in process)
also has the gauge settings that allows you to use the wideband o2 sensor as your narrowband sensor and log it.
89 Voyager LE, 2.5T2 - rest in peace
87 Charger Shelby T2 (2.4 conversion in process)
Where do I go to get the driver for the DLPTXRX board? I can't remember, and I don't see a link on the first page...
assuming it uses the ftdi chip the install software is here:
http://www.ftdichip.com/Drivers/VCP.htm
89 Voyager LE, 2.5T2 - rest in peace
87 Charger Shelby T2 (2.4 conversion in process)
is there any way i can see the timing curve in mpscan ?
Last edited by 2POINT5TURBO; 05-20-2015 at 05:00 PM.