Results 1 to 10 of 10

Thread: GT30R installation: Fittings Needed?

  1. #1
    turbo addict
    Join Date
    May 2007
    Location
    Roanoke, Virginia, United Stat
    Posts
    1,771

    GT30R installation: Fittings Needed?

    Sometime in the future I will bolting up a GT30R and need to know what fittings will be needed to adapt my current Turbo Nation lines (FWD/TU braided line kit) to plumb this turbo. Does anyone by chance have this info?

  2. #2
    Rhymes with tortoise. Turbo Mopar Staff cordes's Avatar
    Join Date
    Dec 2005
    Location
    Tuscola, IL
    Posts
    21,442

    Re: GT30R installation: Fittings Needed?

    I believe ATP turbo has some of the fittings which the GT turbos require. From there you can probably make them work with ease.

  3. #3

    Re: GT30R installation: Fittings Needed?

    that or you will be buying GT series lines

  4. #4
    turbo addict
    Join Date
    May 2007
    Location
    Roanoke, Virginia, United Stat
    Posts
    1,771

    Re: GT30R installation: Fittings Needed?

    Quote Originally Posted by Xtrempickup View Post
    that or you will be buying GT series lines
    GT Series Lines? I am unaware...is there a kit? I can just make up my own but would rather not.

  5. #5
    Boost, it's what's for dinner... Turbo Mopar Staff Aries_Turbo's Avatar
    Join Date
    Dec 2005
    Location
    Warsaw, NY
    Posts
    8,838

    Re: GT30R installation: Fittings Needed?

    what are the coolant ports and the oil line inlet? i assume you would just need some NPT adapter fittings.

    Brian

    Quote Originally Posted by turbovanman
    This one is easy, I have myself to blame, I rush things, don't pay attention to gauges when I should, change to much stuff at once then expect miracles, the list is endless.

  6. #6
    Rhymes with tortoise. Turbo Mopar Staff cordes's Avatar
    Join Date
    Dec 2005
    Location
    Tuscola, IL
    Posts
    21,442

    Re: GT30R installation: Fittings Needed?

    Quote Originally Posted by Aries_Turbo View Post
    what are the coolant ports and the oil line inlet? i assume you would just need some NPT adapter fittings.

    Brian
    I thought they were different on the GT series turbos? I can't imagine why I would see so many people asking about them otherwise.

  7. #7
    Supporting Member Turbo Mopar Contributor "Top Fuel" Bender's Avatar
    Join Date
    Mar 2006
    Location
    Hellertown,Pa
    Posts
    1,963

    Re: GT30R installation: Fittings Needed?

    all the GT stuff I put on the vw's and audi's all use banjo bolts and washers
    not sure on the sizes though
    sorry
    10's AGAIN '07, '08, '09
    TFB Fabrications custom billet machined parts for you Turbo Mopar

  8. #8
    Banned Turbo Mopar Contributor
    Join Date
    Dec 2005
    Location
    Windsor, Ont CANADA
    Posts
    3,805

    Re: GT30R installation: Fittings Needed?

    M14 on the coolant fittings THEY ARE NOT NPT

    dont quote me on the oil feed, but 7/16" male inverted flare fitting sounds right

  9. #9
    Boost, it's what's for dinner... Turbo Mopar Staff Aries_Turbo's Avatar
    Join Date
    Dec 2005
    Location
    Warsaw, NY
    Posts
    8,838

    Re: GT30R installation: Fittings Needed?

    http://www.atpturbo.com/Merchant2/me...egory_Code=GRT

    look at the related items at the bottom of the page. has a bunch of fittings on there.

    Brian

    Quote Originally Posted by turbovanman
    This one is easy, I have myself to blame, I rush things, don't pay attention to gauges when I should, change to much stuff at once then expect miracles, the list is endless.

  10. #10
    Banned Turbo Mopar Contributor
    Join Date
    Dec 2005
    Location
    Windsor, Ont CANADA
    Posts
    3,805

    Re: GT30R installation: Fittings Needed?

    stock lines will be fine once u get the proper fittings

    if yuor runnning internal gate, things get really tight for the oil feed line where the fitting goes. you should find a fitting with a 45 on it (female to male an...whatever size feed line is?? 4an?). use this to attach to the 7/16 fitting in the center section, which will give the feed line clearance to go through the wastegated area.

    i got 2 90s right now doing the job, looks a little funky but its working. once I get a 45 i can elimate these 2 90s and make things look a little cleaner

Similar Threads

  1. brass coolant fittings
    By kwiksilver in forum Turbos & Intercoolers!
    Replies: 11
    Last Post: 05-16-2009, 07:45 PM
  2. Fuel Fuel Rail, AFPR, With fittings NEW!
    By Destro in forum Parts For Sale
    Replies: 0
    Last Post: 08-30-2008, 02:00 AM
  3. brass press fit fittings
    By WickedShelby88 in forum Maintenance & General Tech
    Replies: 2
    Last Post: 04-14-2008, 11:52 AM
  4. Stainless Steel Lines and AN Fittings?
    By Dusty_Duster in forum Maintenance & General Tech
    Replies: 15
    Last Post: 12-05-2007, 07:55 PM
  5. Tips on putting together AN fittings, what a PITA!!!
    By firebaron90 in forum "I need help!"
    Replies: 26
    Last Post: 06-21-2007, 10:37 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •