89 shadow es, built engine, konis, modded!

[shelby zed]

selling/parting my shadow cause i decided tds are ghey. 89 4dr shadow es,

engine specs:
89 t2 2.2 rebuilt with about 10,000k
forged wiseco .020 over pistons (8.5cr)
stock forged rods and crank with .020(i think) clevite 77undersized bearings
rods resized
arp rod bolts, arp main studs, arp head studs
all new seals and gaskets
new intermediate shaft (old one had worn thrust surface so it leaked)
new timing belt
rebuilt head, decked and hot tanked like 5000k ago,
mp headgasket, oem garret t03 (take off from back in the 90s with 15k on it) 2.5 inch swingvalve
srt4 fmic, custom piping (missing one 90 degree bend) all t bolt clamps
braided turbos unleashed coolant and oil lines

fuel/electrical:
mp plus 40s,
shelgame cal(summer:180 speed limiter, rev limit raised, 21psi setup for plus 40s and winter with 120mph speed limit, stock speed limit, 15psi with plus 40s as well)
buick gn adjustable fpr(not installed)
manual fan switch
electronic mbc, stopped working for some reason, didnt investigate to much

drivetrain/brakes/suspension:
A568 small spline from a turbo van (around 200k on it)
reman fenco cvs
stock clutch
srt4 shifter with poly bushings
stock front brakes, rear vented internal drum e brake brakes with new pads, new cables and handbrake setup
red koni adjustable struts front and rear with i think about 25k on them

and im sure much more i cant remember. if anyone has any questions let me know comes with ALL my td spare parts, heads, exhaust manifolds, intake manifolds, throttle bodies, wiring harnesses, transmissions, turbo parts, calipers, valve covers, injectors, and much much more, have about 6k in reciepts which is depressing.. asking 2000 which is less than i have into the motor but there is a catch...


the headgasket blew and i had it towed home, easy fix and you have an insane car, i beat twin turbo rx7s, countless mustangs, camaros, hondas (worth mentioning?) and my uncles srt4. car ran 20psi when it was on the road, and was absolutely terrifying.
please call/text/email Gavin with any questions 250 215 6569 or email mx_racer69@hotmail.com

will trade for turbo stuff or other stuff if anyones got anything interesting. thanks!
car is located in kelowna bc CANADA

[turbovanman²]

Come on, don't give up, we are giving Mission a run this year, a nice fleet of TD's,


Trade Koni's for?

[bgbmxer]

you have been pm'd

[shelby zed]

haha pass simon, sorry. umm trade konis for... 240 parts? need a skyline fmic setup, umm... not sure what else really
and bgbmxr sure, but i want 2 grand for it unless you can work out a deal where someone buys the konis. and shipping would cost you alot if your in pa.

[shelby zed]

and emailing or texting works best then i can get it on my phone, thanks guys for all the interest so far.

[turbovanman²]

Haha, no worries on the Koni's but if I was you, I would sell them seperately, someone would snap those up instantly.

[shelby zed]

fine, konis for sale, buy buy buy what are they worth simon?

[turbovanman²]

fine, konis for sale, buy buy buy what are they worth simon?

A new set just went for $550, struts only, so use that for your feeler.

You know how much they were new, so at least that if they are in good shape.

[bgbmxer]

let me know if you wanna make a deal for the engine

[shelby zed]

i do, not sure how id ship it though? any ideas? and no, didnt port this head before it went on, old one was. umm old intake and exhaust where but i put on stockers so it wouldnt have a huge bump, engine burns absolutely no oil whatsoever, and make me an offer, say 1000 for engine, and 350 for trans? or make a different offer.


simon ill ask 450 for konis with springs?

[turbovanman²]

i do, not sure how id ship it though? any ideas? and no, didnt port this head before it went on, old one was. umm old intake and exhaust where but i put on stockers so it wouldnt have a huge bump, engine burns absolutely no oil whatsoever, and make me an offer, say 1000 for engine, and 350 for trans? or make a different offer.


simon ill ask 450 for konis with springs?

Do you have a local shipping depot? I shipped a long block to the states, they will put it on a crate for you. Its aprox $1.50 a lb to ship an engine.

$450 with springs for all 4? If so, good deal, if only the fronts, still a good deal,

[bgbmxer]

figure out how you would ship it and get back to me

[shelby zed]

ok, someones got dibs on trans and konis in vancouver, ill look into shipping for you and let you know. simon you mean just a post office or?

[89ShelbyGuy]

how much for the mp 40's and shelgames cally?

[bgbmxer]

try calling ups or fedex. someone had something posted up here awhile ago for different shippers but i cant remeber what the site was

[shelby zed]

Ok ill check it out then. 89 shelbyguy with a socketed smec how does 200 sound?

[turbovanman²]

ok, someones got dibs on trans and konis in vancouver, ill look into shipping for you and let you know. simon you mean just a post office or?

Find a shipping depot, IE fed ex center, call them up and tell them you want to ship an engine. The one I use has crates kicking around for this purpose.

Drain all fluids, clean it up and plug up all the holes. They will strap it to the crate and off it goes.

[bgbmxer]

Find a shipping depot, IE fed ex center, call them up and tell them you want to ship an engine. The one I use has crates kicking around for this purpose.

Drain all fluids, clean it up and plug up all the holes. They will strap it to the crate and off it goes.

do they charge by the mile or how does it work

[turbovanman²]

do they charge by the mile or how does it work

Per pound, aprox $1.50.

[bgbmxer]

might not be worth it then we will see i guess