JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
Pulled out trans tonight.
Dean Stillie
87 Shelby Z 2.4 Turbo 9.06@146.05
82 Rampage 2.4 Turbo 10.14@138.02
end in torque converter.
Dean Stillie
87 Shelby Z 2.4 Turbo 9.06@146.05
82 Rampage 2.4 Turbo 10.14@138.02
Hey Dean that looks familiar. most of the time it will take out the pump too.
Ouch on the carnage!
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
2nd time this year?
Yes that was the polished and heat treated shaft. broke in a different spot at least!
Dean Stillie
87 Shelby Z 2.4 Turbo 9.06@146.05
82 Rampage 2.4 Turbo 10.14@138.02
Damn, still haven't broken one of those yet,
1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
2004 GSW TDI, 5 speed, fully loaded, modified.
Aurora ignition wires for sale. Link to info
Super60 roller cams or custom/billet cams. Link to info
That just means you're not hooking up hard enough
Finally got the trans apart. Ordered a new input shaft 300m 904/413 and sending converter out to be fitted with a 904 hub..I hope.
Dean Stillie
87 Shelby Z 2.4 Turbo 9.06@146.05
82 Rampage 2.4 Turbo 10.14@138.02
so have you been holding anything back on your launches?
well I was progressively getting more aggressive but it still hasn't overpowered the brakes and I still haven't use the trans brake on a good launch. Also looking over the data recordings I was only launching it at 14 psi.
Dean Stillie
87 Shelby Z 2.4 Turbo 9.06@146.05
82 Rampage 2.4 Turbo 10.14@138.02
go Dean!!!! give her hell
Nice wrinkleage on those slicks Cory!
I have my input shaft. Converter is out getting fitted, I also have a brace welded in the case...bought myself a tig welder for xmas....I have one set of 3.05-1 ring and pinion but its the earlier one so I'm hoping tomorrow to get a solid pinion gear. Then the trans goes back in woot!!
Dean Stillie
87 Shelby Z 2.4 Turbo 9.06@146.05
82 Rampage 2.4 Turbo 10.14@138.02
good time
is it just me, or does that trans have more lives then a cat?
lol thanks, car hooks up nice...that was brad actually with the red light Maybe you can get some tig experience on my roll cage found out this CM crap should be tigged!! should have went with DOM ooohhh well
Dean is a heart surgeon specialist when it comes to transmissions!! (I was gonna say tranny but we all know what that may lead too )