Looking for '89 2.5 T1 CB, std. bore, bare block.
Delaware area or nearby so I don't have to drive all day to get it.
PM me.
Gary
Looking for '89 2.5 T1 CB, std. bore, bare block.
Delaware area or nearby so I don't have to drive all day to get it.
PM me.
Gary
Last edited by neongary; 02-26-2009 at 11:14 PM.
Nobody?
I have a used one, need to check it over but of course, shipping is a concern, its a $1.50 ish a pound.
1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
2004 GSW TDI, 5 speed, fully loaded, modified.
Aurora ignition wires for sale. Link to info
Super60 roller cams or custom/billet cams. Link to info
I have one in jacksonville,fl
Bump. Still looking.
I'm near detroit, but I have one with only 12,000 original miles ready to bolt in, its all standard and needs nothing. It ran great, no smoke, no engine noise. big psi bought the head off it and will tell you its condition. I sold the head because I was going to put my big valve g head on it. I got carried away with mods and I need forged pistons. It makes no sense to me to rebuild this engine its like new and just broken in. its not rebuilt only 12,000 original miles. its been stored indoors since the lebaron was totaled in 1990. it was oiled up and turned every few months. no rust inside it, never taken apart, ready to go. I put it in my van last year with a super 60, and ffv injectors stock intercooler, and custom cal. I never drove it but heard it run myself. Its a good motor and in my opinion better than a rebuild or replacement engine. I'm asking 500 or best offer. its a bit of a drive but worth it.
Are you looking for it to remain a std bore? I'm about to pull an 89 2.5 TI from my car. The reason I ask about the bore is the motor currently doesn't turn over. Ran when I parked it but I believe the head checked thus the rings may have rusted to the cylinder walls.
I assume any N/A or turbo CB block out there in DE is rare as hen's teeth?
ANY CB can be made a 2.5 turbo block once you drill a hole in the back of the block(5 min job), but I'm sure you knew that already...
-Nate- ''Sometimes I wonder whether the world is being run by smart people who are putting us on, or by imbeciles who really mean it.'' —Mark Twain
Found one. Thanks everyone.
Nate: Actually hens teeth in Delaware are quite common as the Blue Hen is the state bird, but apparently the 2.5 isn't as common in local jy.
Last edited by neongary; 02-27-2009 at 08:34 PM.
Does your hen have sharp talons?
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
I have a 92 2.5commonblock running motor complete that has 166K on it. it is N/A but it sounds like you want it bare so the block and crank and whatever is same, pistons are different. could pull and have it ready to depart NJ anytime really if you wanted it, im about 3-4 at most from anywhere in DE. asking 175$