Page 1 of 3 123 LastLast
Results 1 to 20 of 48

Thread: My clearing out the garage sale

  1. #1
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    My clearing out the garage sale

    Most of these parts came with a project car and I need some space. Most of it looks to be 87 stuff but there was some common block stuff in it also. If you need more pics of anything just let me know. I will not be holding onto most of this very long before it goes to the scrap yard.

    CB 2.5 cast crank. $35 + ride, weight on it is 39 lbs.

    Stock style clutch -Sold, 8 bolt flywheel $15.

    Turbo valve covers $15 each. SRT cover free with any purchase.

    1 piece fuel rail, regulator and harness $20.

    FMU $30.

    New rad hoses. $10 each. Used one $5.

    46mm TB $15, 52mm TB $20, 2 square tooth cam sprockets $10 each,square tooth crank sprocket $10, round tooth I - shaft sprocket $5, blasted water pump housing $30, other water pump $10, blasted rear main seal housing with new seal $10, all other pulleys, mounts and covers $5 each.


    Alternator for core, $10.

    92 Daytona carpet, $20.


    All of the shiny looking brackets, etc are sand blasted with light surface rust. Nothing a brilo pad won't clean up.

    I will hold and deliver parts to anyone at the Chrysler Classic at Norwalk in a couple weeks, Lebanon Valley Mopar Day and the annual Cecil Fun day. Make a reasonable offer on the stuff and it's yours. I don't have any use for most of this stuff. Shipping is not included, and all prices are negotiable.
    Last edited by Turbo3Iroc; 04-12-2009 at 11:32 AM. Reason: updated sold parts

  2. #2

    Re: My clearing out the garage sale

    Kelly I might be intrested in the clutch and carpet what type of trans will the clutch work in ?
    paul B
    What type of paymet do you take?

  3. #3
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    I take paypal or postal money order. The clutch looked like a small spline, I'll verify it in a bit.

  4. #4
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    It is small spline, interested?

  5. #5
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    Few more I found:

    P body cluster showing 111k, $20

    P body seat brackets, $10

    Crank pulley with a/c $5.

    87 style sway bar bushings, $15.
    Last edited by Turbo3Iroc; 09-01-2008 at 09:13 PM.

  6. #6
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    Last ones today:

    Stock 2.5" down pipe out of a Spirit R/T. Has flange but no donut. $25

    Stock springs out of same Spirit R/T, $40

    Slapper bars bought for my old Dakota. May fit other applications. $20
    Last edited by Turbo3Iroc; 09-01-2008 at 09:14 PM.

  7. #7

    Re: My clearing out the garage sale

    how much for the TI 87 engine harness, and sway bar bushings? Shipped to 74028

  8. #8
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    PM sent

  9. #9
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale


  10. #10

    Re: My clearing out the garage sale

    how much for the 2.5l crank shipped to 66502? Thanks.

  11. #11
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    Shipping looks to be ~$32 via fed ex, $70 sound good?

  12. #12
    Supporting Member Turbo Mopar Contributor Turbo Joe's Avatar
    Join Date
    Dec 2005
    Location
    South Coast Ma.
    Posts
    884

    Re: My clearing out the garage sale

    hey Kelly, that fuel pressure unit is commonly called a F.M.U. fuel management unit.
    btw let me know if you still have the dash wiring from that 87.. thanks..
    Turbo Joe
    ----------------------- 87 CSX #175 TIII powered, MegaSquirt3 Pro Ultimate, GTX3076R, Turbo Joe header, Lengel intake, Menegon ported head, the list goes on

  13. #13
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    Hey Joe, thanks for identifying that. Can you tell me more of its use?

    The harness is still attached to the car. I do not know if it is complete. You need the whole thing or just part of it?

  14. #14
    Super Moderator Turbo Mopar Staff 135sohc's Avatar
    Join Date
    Aug 2008
    Location
    SoMd
    Posts
    6,178

    Re: My clearing out the garage sale

    is that a cable drive P body cluster ?

  15. #15
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    Yes it is cable drive.

  16. #16
    turbo addict
    Join Date
    Nov 2006
    Location
    san diego, california
    Posts
    1,548

    Re: My clearing out the garage sale

    i would like the fmu, i would like to know how to use it in my application also. i already have an acufab(?) adjustable fpr,think i need to run the fmu to run my +20s(flex fuel +18s) without a cal?

  17. #17
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    I do not know anything about the fmu as I posted above. It came with a car I bought and I have no use for it.

  18. #18
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    I've replied to all PM's. If the prices I have quoted are out of your budget make an offer. Need to move this stuff.

  19. #19
    See me ride out of the sunset... Turbo Mopar Staff BadAssPerformance's Avatar
    Join Date
    Dec 2005
    Location
    Chicagoland!
    Posts
    27,688

    Re: My clearing out the garage sale

    Gotta list prices please...

    What do the bar bushings fit if not already taken?

    JT
    SDAC Director
    SDAC-Chicago President
    JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
    87 Shelby Z - 10.50@141.66mph
    87 CSX #751 Clone - 12.88@102.88mph

    www.badassperformance.com
    Check out Turbo-Mopar Times!
    Submit your 1/4 mile times HERE!!

    Support SDAC! Join Today!
    "I'm not some pro athlete with a bajillion dollars, I'm just an every man"
    Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.

  20. #20
    turbo addict
    Join Date
    Dec 2005
    Location
    Bristol, CT
    Posts
    2,722

    Re: My clearing out the garage sale

    So much stuff and I don't know what much of it is worth. You know I'm a T3 guy lol. This stuff came in a shell I bought.

    The bushings are for the early K member.

Page 1 of 3 123 LastLast

Similar Threads

  1. garage sale parts for sale
    By 1FastCSX289 in forum Parts For Sale
    Replies: 14
    Last Post: 09-15-2007, 08:25 PM
  2. LAST CHANCE (85 turbo z) plus garage sale
    By midohiomoparsource in forum Parts For Sale
    Replies: 6
    Last Post: 03-22-2007, 02:59 PM
  3. Cleaning garage sale
    By midohiomoparsource in forum Parts For Sale
    Replies: 9
    Last Post: 01-07-2007, 07:11 PM
  4. Garage sale
    By Will Martin in forum Parts For Sale
    Replies: 28
    Last Post: 08-02-2006, 12:43 AM
  5. JT's Year End Garage Sale!!!
    By BadAssPerformance in forum Parts For Sale
    Replies: 19
    Last Post: 12-31-2005, 11:32 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •