rebuild on my 88 shelby z 2.2 and am having trouble with the MAP sensor, code 13, have tried a different one but the same problem exists and computer goes into limp in mode.
Does any one have the electric reading for the MAP sensor and the solenoid?
rebuild on my 88 shelby z 2.2 and am having trouble with the MAP sensor, code 13, have tried a different one but the same problem exists and computer goes into limp in mode.
Does any one have the electric reading for the MAP sensor and the solenoid?
Code 13 is the MAP not seeing a vacuum change, check for vacuum at the hose and if necessary, bypass the BARO just to make sure its not bad.
1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
2004 GSW TDI, 5 speed, fully loaded, modified.
Aurora ignition wires for sale. Link to info
Super60 roller cams or custom/billet cams. Link to info
as always Simon, ready to share your knowledge, thanks.
Found what the problem was with the vacuum, the hose was on the wrong side of the sensor.
Ken tells me we have already done that, what he needs to establish is if the computer is operating properly. What values form the computer at the MAP sensor?
Does that make sense? I am way out of my league and learning like crazy.
I found this information and am assuming that this is what I am looking for.
Map Sensor Response Chart Turbocharged
Pressure in Inches/HG to Voltage
24.01HG/.43V
18.11HG/.93V
12.20HG/1.42V
6.30HG/1.92V
.39HG/2.41V
2.71PSIG/2.91V
5.61PSIG/3.41V
8.51PSIG/3.90V
11.31PSIG/4.40V
14.31PSIG/4.90V
TPS Response Chart
Throttle Position in Degrees to Increase of Minimum TPS Volts
Closed Throttle
10 DEGS/0.00V
20 DEGS/0.38V
30 DEGS/0.75V
Half Throttle
45 DEGS/1.31V
58 DEGS/1.80V (1)
75 DEGS/2.43V (2)
Wide Open Throttle
90 DEGS/3.00V
(1) The computer will usually consider an increase of 1.80 volts or more over the minimum TPS voltage to be WOT.
(2)2.43 volts above the minimum TPS voltage during cranking will cause the computer to recognize Clear Flood request shutting off all fuel delivery.
So what problem do you have now? Still code 13?
What is the koeo vacuum reading at the MAP? Idling?
1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
2004 GSW TDI, 5 speed, fully loaded, modified.
Aurora ignition wires for sale. Link to info
Super60 roller cams or custom/billet cams. Link to info
Still code 13, but now with that information going to check and see what the readings are.