A true S60 roller cam-now available-regrind or new billet!

[4cefedomni]

hey simon put me down for a regrind and i'll drop off the money and a core next time i'm out your way. do you think this will work with your springs and a set of solid lifters? or will the solid lifters put the lift out of the range of those springs?

[turbovanman²]

hey simon put me down for a regrind and i'll drop off the money and a core next time i'm out your way. do you think this will work with your springs and a set of solid lifters? or will the solid lifters put the lift out of the range of those springs?

I don't think the lifters will alter anything, just make sure to adjust them properly.

[moparzrule]

So simon we got atleast 6 now? Just give me an address to send the core, and paypal addy for the $.

[turbovanman²]

Ok, going to PM each of you and get this going. We have 5 for sure, with a possible of 7.

The list so far-


1) Moparzrule-regrind-maybe!
2) John B-new billet and springs.
3) Denny-regrind.
4) Sean-regrind if funds permit.
5) Don-regrind.
6) Ryan-Sloride-new billet.

[moparzrule]

Aren't you getting one Simon??? Do you definitely have 6 now?

I'm a definite now, I sent you the core cam yesterday!

[turbovanman²]

Aren't you getting one Simon??? Do you definitely have 6 now?

I'm a definite now, I sent you the core cam yesterday!

What am I going to run it in? I am not that good that I can make it work in both my TIII's.

[moparzrule]

Not that I'm complaining, but why are you even offering this then?

[turbovanman²]

Not that I'm complaining, but why are you even offering this then?

Because I am a vendor and am trying to make spare cash to pay for things,

[John B]

And I pestered him a bit...

[John B]

What am I going to run it in? I am not that good that I can make it work in both my TIII's.

It's not the right timing/lift for a 16V anyway, even if you could make it fit.

[moparzrule]

It's not the right timing/lift for a 16V anyway, even if you could make it fit.

Hehe, yeah .499 lift is a bit much for a 16V LOL.

[moparzrule]

Because I am a vendor and am trying to make spare cash to pay for things,

Thats cool, was just wondering. Thanks

[turbovanman²]

OK, update on payments-

Denny-pending
Slo60-Paid
Don-Paid
Matt-paid
John-Paid
and I am getting one done to keep on hand.

Looks like I can get them started next week.

Ok, due to Denny's circumstance, I am getting them made. I'll be dropping off the money on Tuesday, March 4th and get them made.

Thanks guys.

[John B]

I believe this cam will be the "magic bullet" for my combo. Thanks again Simon for making it happen!

[turbovanman²]

I believe this cam will be the "magic bullet" for my combo. Thanks again Simon for making it happen!

Thanks for giving me a kick in the arse,

[Sloride]

*boots arse*
check your pm box plz



(if one was good, two must be better )

[turbovanman²]

*boots arse*
check your pm box plz



(if one was good, two must be better )

OUCH,

I'll get to the Post Office tomorrow, to busy today.

[turbovanman²]

See update above.

[turbovanman²]

Cams are ordered, he said I got him at a bad time-he just got a huge Cummings IP cam order but 1.5-2 weeks and there done. In order to get the deal, I had to buy one myself as a few guys changed there minds or ran out of funds. So I will update when I pick them up, then I will be shipping them out.

Denny, hope things are ok also.

****Note again, these are based on the Super60 slider cam so if using on a round tooth setup, you will need to degree them**********

[moparzrule]

Why can't he make it for the round tooth? Is it that hard to change? I think the majority if ot all of us have the round tooth sprocket.