Results 1 to 15 of 15

Thread: Alternate parts thread-OEM to aftermarket-post findings!

  1. #1
    Hybrid booster
    Join Date
    Dec 2005
    Location
    Crestwood, Kentucky
    Posts
    277

    Alternate parts thread-OEM to aftermarket-post findings!

    Thanks to Simon and others who contributed to the original thread...

    Post parts you have found that fit TIII's that are from other cars, and aftermarket suppliers.

    1.) The front crank seal is CR part #11111,

    2.) The cam seals are #14707-CR stands for Chicago Rawhide. You can use these numbers to cross over to any other brand, IE National etc.

    3.) Dodge Viper oil cap, I took the gasket off the Viper oil cap and put it on my stocker.

    4.) TI/TII/TBI commonblock can be substituted for a trashed TIII block. Grind in the water pump passage area for clearance for the water deflector. Place a core plug in the distributor hole. Crankcase breather can be added by drilling a hole in the distributor core plug and installing breather there (before installing plug!). TBI block will also need to be drilled for turbo oil return on the rear of block.

    5.) Substitute thermostat gasket: Use a thermostat gasket from a '94 Dodge 5.2 V8.

    6.) Head studs... Acura VTEC B18C1, 11mm. arp part number 208-4303 they are the 11mm ones for the 1.8 vtec. I had to go this route when building my engine because our vendors were out of stock, but everyone and their mothers sell honda parts.

    7.) Part numbers through Goodyear for:
    Radiator hose, upper 61782
    Idler pulley/Serp tensioner pulley's- 49038
    Radiator hose, lower 61341
    Timing belt 40206
    Heater hose, heater to waterpump 63073
    Serpentine belt 4060785
    Heater hose, heater to engine 63275

    Belt numbers for no a/c or UDP.

    Stock belt: 060790
    Non A/C: 060660
    Non A/C & UDP: 060637

    I found Dayco belt # 5060670 fit with no a/c, the 60 was too short.

    You insert vendors choice for the first number, IE Dayco would be a 5060790, Goodyear a 4060970 etc.
    Last edited by turbovanmanČ; 10-03-2007 at 03:28 PM.

  2. #2
    turbo addict
    Join Date
    Dec 2005
    Location
    MOTOR CITY
    Posts
    1,570

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Category/ Part/ Brand/ Aftermarket Part # / OEM Equivalent
    Sensors
    Crankshaft Position Sensor:
    Borg Warner CSS72
    Niehoff AL2024

    Camshaft Position Sensor:
    Borg Warner CSS74

    Oxygen Sensor (4 wire):
    Bosch 13275

    Fuel Injector (4 total):
    GP Sorenson 800-1047N 5277895

    Washer Fluid Level Sensor - Front:
    Niehoff AL1005

    Washer Fluid Level Sensor - Rear:
    Niehoff AL1006

    Coolant Level Sensor:
    Niehoff AL1010

    Water Temp. Switch (Gauge):
    GP Sorenson TSU113

    Ambient Air Temp Sensor (For Overhead Console Cars):
    GP Sorenson TSU180

    Air Charge Temp Sensor:
    Niehoff TS81261

    Throttle Position Sensor:
    Niehoff FE1088 5234901
    Standard TH136 5234901

    Knock (Detonation) Sensor:
    GP Sorenson KS1 5213629
    Borg Warner S799 5213629
    Standard KS1 5213629

    M.A.P. Sensor:
    Niehoff FE-1627 5234327
    Standard AS25 5234327

    Idle Air Control Valve:
    Niehoff 21811 4612159; 4612673; 5277839
    Borg Warner 21811 4612159; 4612673; 5277839

    Coolant Temperature sensor (2 Pin):
    Niehoff TS82231
    GP Sorenson TSU110

    Coolant Temperature sensor (3 Pin):
    GP Sorenson TSU89 4267281

    Oil Pressure Switch (Gauge):
    GP Sorenson OPS121

    Fuel Pressure Regulator:
    Niehoff 22823 4306015

    Fuel Pump (Assembly Including Pump and Strainer):
    Carter P74631H

    Fuel Tank Sending Unit (Float Gauge Assembly):
    Spectra Premium FG64B

    Fuel Tank (Daytona):
    Spectra Premium CR2G

    Fuel Tank Straps (Daytona):
    Spectra Premium ST17

    Engine Mounts:
    Right Side Motor Mount (Upper Passenger Side) Anchor 2616
    Poly Bushings #1000 Note: this mount is polyurethane

    Front Motor Mount (Below Radiator on Core Support):
    Anchor 2615
    Poly Bushings #3419 Note: this mount is polyurethane

    Engine Gaskets and Seals
    Rear Main Seal :
    National 710056 4621939AB, 4667904, MD101915, 4621939, 4667322, 5203590, MD120699
    Fel-Pro BS40168-1 Made From Rubber, One Piece
    Fel-Pro BS40627 Made From Teflon, One Piece
    Timken 710056 Made From Viton, One Piece
    Timken 5279 Made From Teflon, One Piece

    Intake Manifold Gasket (Plenum Gasket set):
    Standard PG34 4343703

    Intake Manifold Gasket and Exhaust Manifold Gasket Set:
    Mopar 4728214AB

    Front Crank Seal:
    Chicago Rawhide 11111 4273275
    National 3638 4273275
    Gates KS11122
    Timken 3638

    Front Crank Seal Repair Sleeve:
    National 99112
    Timken KWK99112

    Camshaft Seal (2 Required):
    Chicago Rawhide 14707 4424059
    National 223801 4424059
    Gates KS13948
    Timken 223801

    Camshaft Seal Repair Sleeve (2 Required):
    National 99147
    Timken KWK99147

    Auxiliary Shaft Seal :
    National 3655 4105388, 4105389, 4105395, 5203465

    Auxiliary Shaft Seal Repair Sleeve:
    National 99139

    Water Outlet Gasket:
    Fel-Pro 35286

    Head Gasket:
    Mopar 5013602AA
    Cometic C5733-65 This is a Multi - Layer Steel - Shim Gasket 0.065 Inches Thick

    Valve Cover Gasket (Sold Individually):
    Mopar 4484489

    Valve Stem Seals (Sold in Set of 16):
    Mopar 4424030

    Engine Miscelianious
    Timing Belt:
    Mopar 4667530
    Gates T206
    Goodyear 40206
    Dayco 95206

    Head Bolts:
    Mopar 6502219
    ARP 241-3701 12-Point Head

    Head Studs:
    ARP 241-4501 Hex Nuts
    ARP 241-4701 12-Point Nuts

    Main Studs:
    ARP 141-5401

    Connecting Rod Bolts:
    ARP 141-6001 High Performance Complete
    ARP 141-6021 High Performance 2 piece
    ARP 141-6401 High Performance Wave Complete

    Camshaft Sprockets:
    FWD Performance FWD 43-0802 Note: These Sprockets are Adjustable and Available in Multiple Colors

    Lifters (Set of 16):
    FWD Performance fwd 43-0199

    Oil Fill Cap:
    Stant 10066
    Gates 31066

  3. #3
    turbo addict
    Join Date
    Dec 2005
    Location
    MOTOR CITY
    Posts
    1,570

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Electrical
    Horn - Low Note:
    Niehoff UN451

    Horn - Low Note (High Out Put):
    Niehoff UN458

    Horn - High Note:
    Niehoff UN450

    Horn - High Note (High Out Put):
    Niehoff UN457

    Power Window Switch (Driver's Side; 2 Button):
    Mopar 4688229
    Niehoff MC56591
    Dorman 49224

    Rear Defogger Switch (Daytona):
    Niehoff MC59101

    Cruise Control Switch Assembly (Daytona):
    Niehoff CC21211

    Back-up light Switch:
    Niehoff NS37011

    Door Jam Switch (Courtesy Lamp Located on A - Pillar):
    Niehoff DJ40201

    Door Jam Switch (Door Ajar Located on B - Pillar):
    Niehoff DJ40211

    Head Lamp Switch Assembly (Daytona W/ Fog Lamps):
    Niehoff HL20201

    Turn Signal Switch:
    Niehoff DS50111

    Ignition Switch (Daytona):
    Niehoff IG69301

    Front Windshield Washer Pump:
    Niehoff WP7966
    Trico 11-514
    Dorman 88113

    Rear Tailgate Washer Pump:
    Trico 11-507
    Dorman 88114

    Front Windshield Wiper Motor:
    Dorman 601-300 Note: This Part is New
    Cardone 85-388 Note: This Part is New
    Cardone 40-388 Note: This Part is Remanufactured

    Rear Windshield Wiper Motor:
    Cardone 40-397 Note: This Part is Remanufactured

    Turbo
    Blow Off Valve:
    Mopar 4504564


    Heating and Cooling
    Water Pump (New):
    GMB/ Prestone 120-3060 4626682/ O.E. Casting #4483455

    Thermostat:
    Prestone 338-192

    Bypass Hose (Heater to Engine):
    Goodyear L-63275
    Gates 18948

    Bypass Hose (Heater to Water Pump):
    Goodyear 63073
    Gates 18075

    Bypass Hose (Heater to Oil Cooler):
    Gates 18987

    Upper Radiator Hose:
    Goodyear 61782
    Gates 21639
    Dayco 71279

    Lower Radiator Hose:
    Goodyear 61341
    Gates 21674

    Idler Pulley:
    Goodyear 49013

    Tensioner Pulley:
    Goodyear 49038

    Serpentine Belt:
    Goodyear 4060785 or 785K6
    Gates K060785
    Dayco 5060785

    Radiator Fan Assembly (Motor Included):
    Dorman 620-008

    Radiator Fan Motor :
    Seimens PM3310

    Radiator Cap:
    Stant 10231 or 10331 Note: Cap is Rated at 16 PSI
    Gates 31516 or 31523 Note: Cap is Rated at 16 PSI

    Air Conditioning
    A/C Low Pressure Cut-out Switch:
    Niehoff HS-30271

    A/C Condenser:
    Factory Air 54329

    A/C Receiver Drier/ Accumulator:
    Four Seasons 33550

    A/C Evaporator Core:
    Four Seasons 54109

    A/C Expansion Valve (Block Type Flange):
    Four Seasons 38849

    A/C Compressor (Remanufactured LTR4, With Clutch):
    Four Seasons 57235

    Selector Vacuum Switch:
    Niehoff HS-30341

    Blower Control Switch:
    Niehoff HS-80511

    Blower Motor:
    Siemens PM299
    Last edited by rich tideswell; 12-25-2010 at 04:57 PM.

  4. #4
    turbo addict
    Join Date
    Dec 2005
    Location
    MOTOR CITY
    Posts
    1,570

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Engine Filters and Tune-Up

    Air Filter:
    Fram CA3660

    P.C.V. Valve:
    Fram FV163

    Crankcase Breather Filter:
    Fram BA6662

    Carbon Canister Filter (4.5in Dia.):
    GP Sorenson 779-1000

    Ignition Coil:
    Wells C939

    Spark Plug:
    Champion RN12YC Copper
    Champion 3405 Platinum
    NGK GR4IX Iridium
    NGK GR4GP Platinum
    NGK GR4 V-Power
    Bosch WR8DP Platinum
    Splitfire SF6C Copper
    Splitfire TP6C Platinum

    Spark Plug Wire Set:
    Accel 5109R Note: wires set is red

    Chassis and Suspension
    Power Steering Pressure Hose:
    Edelmann 71918

    Power Steering Return Hose:
    Edelmann 71899

    Power Steering Pump:
    Cardone 20-863 frim feel stearing code SBA; Note: this part is remanufactured

    Power Steering Pump Cap:
    Dorman 82577

    Power Steering Pressure Sensor:
    Niehoff AL9000

    Complete Power Steering Pump Rebuild Kit:
    Gates 350390

    Rear Track Bar Replacement Bushings:
    Poly Bushings #1025 Note: this part is polyurethane

    Rear shock:
    KYB 343164

    Rear Axle to Frame Bushings:
    Poly Bushings #1036

    Front Strut:
    KYB 235045

    Front Strut Upper Mount with bearing:
    Monroe 901908

    Front Strut Upper Spring Seat:
    Monroe 902993

    Front Strut Lower Spring Seat:
    Monroe 903980

    Front Lower Ball Joint:
    TRW 104178

    Inner Tie Rod:
    TRW ES3061R

    Outer Tie Rod End:
    TRW ES3008R

    Rack and Pinion Assembly:
    Cardone 22-336 frim feel stearing code SBA, manual trans, 16inch wheels; Note: this part is remanufacuted

    Rack and Pinion Assembly Mounting Bushing:
    TRW HB1212

    Lower Control Arm Bushings:
    TRW HB1750K

    Sway Bar Bushing to Control Arm 1" Bar:
    TRW HB1806

    Sway Bar Bushing to Frame 1" Bar:
    TRW HB1620

    Sway Bar Bushing to Control Arm 1 1/16" Bar:
    TRW HB1807

    Sway Bar Bushing to Frame 1 1/16" Bar:
    TRW HB1621

    Sway Bar Bushing to Control Arm 1 1/8" Bar:
    TRW HB1616

    Sway Bar Bushing to Frame 1 1/8" Bar:
    TRW HB1622

  5. #5
    turbo addict
    Join Date
    Dec 2005
    Location
    MOTOR CITY
    Posts
    1,570

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Brakes
    Front Brake Pads; Semi - Metallic:
    Raybestos PGD522M

    Front Brake Rotor:
    Raybestos 7992

    Front Brake Caliper - Right:
    Reman Parts Inc. 4315 OEM Casting #12391901 ; Note This Part is Remanufactured
    Dorman CA10904R O.E.M. #4423716 ; Note: This Part is New
    Cardone 18-4362 Supplied With Hardware, Phenolic Piston Supplied Without Mounting Bracket
    Cardone 18-B4362 Supplied With Hardware, Phenolic Piston Supplied With Mounting Bracket
    Cardone 18-4362S Supplied With Hardware, Metal Piston Supplied Without Mounting Bracket
    Cardone 18-B4362S Supplied With Hardware, Metal Piston Supplied With Mounting Bracket
    Cardone 16-4362 Supplied With Pads and Hardware Phenolic Piston
    Cardone 16-B4362 Supplied With Pads and Hardware Metal Piston
    Cardone 15-4362S Supplied With Servre Duty Pads And Hardware Phenolic Piston
    Cardone 15-B4362S Supplied With Servre Duty Pads And Hardware Metal Piston

    Front Brake Hose With ABS - Right:
    Coni - Seal BH177917

    Front Brake Caliper - Left:
    Reman Parts Inc. 4316 OEM Casting #12391901 ; Note: This Part is Remanufactured
    Dorman CA10903L O.E.M. #4423717 ; Note: This Part is New
    Cardone 18-4363 Supplied With Hardware, Phenolic Piston Supplied Without Mounting Bracket
    Cardone 18-B4363 Supplied With Hardware, Phenolic Piston Supplied With Mounting Bracket
    Cardone 18-4363S Supplied With Hardware, Metal Piston Supplied Without Mounting Bracket
    Cardone 18-B4363S Supplied With Hardware, Metal Piston Supplied With Mounting Bracket
    Cardone 16-4363 Supplied With Pads and Hardware Phenolic Piston
    Cardone 16-B4363 Supplied With Pads and Hardware Metal Piston
    Cardone 15-4363S Supplied With Severe Duty Pads and Hardware Phenolic Piston
    Cardone 15-B4363S Supplied With Severe Duty Pads and Hardware Metal Piston

    Front Brake Hose With ABS - Left
    Coni - Seal BH177916

    Front Brake Caliper Seal Kit - 60mm Piston:
    Coni - Seal 66517

    Front Brake Caliper Banjo Bolt:
    Dorman 13939 Thread: 7/16 x 20; Length: 7/8 inch; Hex Size: 5/8 inch

    Front Brake Caliper Slide Bolts:
    Carlson H5066 comes in a set of 2 bolts and 2 sleeves

    Front Wheel Stud:
    Dorman 98480 M12 x 1.5

    Rear Brake Pads; Semi - Metallic:
    Raybestos PGD415M

    Rear Brake Rotor (Vented):
    Raybestos 7993

    Rear Brake Rotor (Non - Vented):
    Raybestos 76002

    Rear Brake Caliper - Right (Vented Rotors):
    Reman Parts Inc. 4303 OEM Casting #120753

    Rear Brake Caliper - Right (Non - Vented Rotors):
    Reman Parts Inc. 4301 OEM Casting #120492

    Rear Brake Caliper - Left (Vented Rotors):
    Reman Parts Inc. 4304 OEM Casting #120753

    Rear Brake Caliper - Left (Non - Vented Rotors):
    Reman Parts Inc. 4302 OEM Casting #120492


    Rear Brake Hose:
    Coni - Seal BH177809

    Rear Brake Cable - Right:
    Raybestos BC93944

    Rear Brake Cable - Left:
    Raybestos BC93944

    Rear Parking Brake Hardware Raybestos:
    F138098S

    Rear Wheel Stud (Rear Disc Brake Equipped):
    Dorman 97045 M12 x 1.5

    Wheel Lug Nuts (Chrome Capped) Dorman 98976 M12 x 1.5

    Brake Master Cylinder:
    Cardone 13-1983 Note: New; Reservoir Included
    Cardone 10-1983 Note: this part is remanufactured, no reservior

    Power Brake Booster (Remanufactured):
    Cardone 54-73172

    Stop Light Switch (Daytona):
    Niehoff SL-78211

    ABS Hydraulic Unit (Remanufactured):
    Cardone 12-2107

    ABS Control Module:
    Cardone 12-1103 5234235

    ABS Sensor - Front Right:
    Raybestos ABS530348

    ABS Sensor - Front Left:
    Raybestos ABS530349

    ABS Sensor - Rear Right:
    Raybestos ABS530080

    ABS Sensor - Rear Left:
    Raybestos ABS430351

    ABS Relay:
    Niehoff RL-35491 O.E.M. #4687246

    Master Cylinder Cap:
    Dorman 42044

    Master Cylinder Cap Gasket:
    Dorman 42081

    Brake Pedal Pad:
    Dorman 20727

    Spindle Nut - Front :
    Dorman *05183

    Spindle Nut - Rear
    Dorman *05190

    Front Hub Assembly:
    SKF CBR930013
    SKF BR930013
    BCA/ National 513075
    Timken 513075

    Rear Inner Bearing:
    BCA/ National A-39
    Timken Set46

    Rear Outer Bearing:
    BCA/ National A-16
    Timken Set16 Note: Bearing has Stamping LM12749F, and Race has Stamping LM12711

    Rear Inner Seal:
    BCA/ National 4099
    Timken 4099

    Rear Wheel Dust cap:
    Dorman 13975

    Transmission/ Clutch/ Axle
    Manual Transmission Mount (Mid shock tower, driver's side):
    Anchor 2618
    Poly Bushings #PB2618 Note: this mount is polyurethane

    Manual Transmission Bobble Strut:
    Poly Bushings #3297 Note: this part is adjustable

    Clutch Pedal Pad:
    Dorman 20727

    Shifter Cable :
    Dorman 16653

    Clutch Cable:
    Raybestos BC94374
    Autospecialty CA-83007

    Clutch Release Bearing:
    Timken 614092
    BCA/ National 614092

    New Clutch Set:
    Fenco NU0066SC

    Clutch Fork:
    Dorman 14565

    Inner Clutch Fork Bearing:
    Dorman 14337

    Outer Clutch Fork Bearing:
    Dorman 14345

    Clutch Switch:
    Niehoff AL-2500

    Differential Bearing (2 Required)
    Timken Set11

    Differential Bearing Repair Sleeve (2 Required):
    Timken KWK99157

    Differential Housing Seal:
    Timken 3459S
    National 3459S

    Input Shaft Bearing:
    Timken Set4

    Input Shaft Seal - Front:
    Timken 3732S

    Input shaft Seal Repair Sleeve - Front:
    Timken KWK99106

    Input Shaft Bearing - Rear:
    Timken Set5

    Axle Shaft - Left Side:
    USA Industries AX-65299 Note: This Part is Remanufactured
    Cardone 60-3025 Note: This Part is Remanufactured
    Cardone 66-3025 Note: this Part is New

    Axle Shaft - Right Side
    USA Industries AX-65299 Note: This Part is Remanufactured; Equal Length Driveshafts
    Cardone 60-3025 Note: This Part is Remanufactured; Equal Length Driveshafts
    Cardone 66-3025 Note: This Part is New; Equal Length Driveshafts
    USA Industries AX-65309 Note: This Part is Remanufactured; Un-Equal Length Driveshafts
    Cardone 60-3034 Note: This Part is Remanufactured; Un-Equal Length Driveshafts
    Cardone 66-3034 Note: This Part is New; Un-Equal Length Driveshafts

    Inner CV Boot:
    Dorman 614-002

    Outer CV Boot:
    Dorman 614-003

  6. #6

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Nice job Rich!

  7. #7
    turbo addict Tony Hanna's Avatar
    Join Date
    Dec 2005
    Location
    Charleston, WV
    Posts
    3,223

    Thumbs up $38 TIII Crankshaft Position Sensor!

    GP Sorensen part # CSS40 $38.88 normally stocked (Advance Auto Parts)

    It requires cutting the plastic back around the plug, and soldering the pigtail from your old sensor (or a spare HEP... same connector ) to the terminals. It also requires filing a flat into the plastic body of the new sensor in the same location as the flat on the stock sensor. Other than that, it's a drop-in replacement. The body is the same length, and the bolt hole is in the right spot.
    I just got my Spirit running off of one today, so no long term results yet, but it's working great so far.
    Maybe someone else can benefit from my experimenting. Sure beats paying $150-$200 for one.

  8. #8
    turbo addict Tony Hanna's Avatar
    Join Date
    Dec 2005
    Location
    Charleston, WV
    Posts
    3,223

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Paint:
    Code PRB Radiant Fire
    Duplicolor
    1/2 oz bottle/brush (scratch fix) part# NGCC382
    5 oz spray can part # DSCC382

  9. #9

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    ARP-200-8530 7/16ID 13/16OD BLK WASHER

    Is the washer that is used with the ARP Studs

  10. #10
    Garrett booster
    Join Date
    Nov 2009
    Location
    boston-ish
    Posts
    54

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    4 into 1 vacuum connector on front of block from Dodge. (part# 04504024)

  11. #11
    Hybrid booster 4cefedomni's Avatar
    Join Date
    Mar 2006
    Location
    Delta B.C. Canada
    Posts
    694

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    How is this not in the KC?
    you can't polish a turd! [COLOR="Red"][FONT="Arial Black"][/FONT][/COLOR]13.67@100.11

  12. #12
    Garrett booster
    Join Date
    Apr 2011
    Location
    Winnipeg Canada
    Posts
    71

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    thank you for this post! Great resource wish I had found this years ago!

  13. #13
    turbo addict
    Join Date
    Jan 2007
    Location
    South Gillies, ON. Canada
    Posts
    2,923

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Quote Originally Posted by 4cefedomni View Post
    How is this not in the KC?
    i second that.
    1988 Lancer Shelby 2.2TII 1989 Shadow ES 2.5TI 1992 Lebaron Sedan 3.0Auto 1993 Acclaim 2.5TI-A520 Hoard parts now!

  14. #14
    Buy my stuff!!!!!!!!!!! :O) Turbo Mopar Vendor turbovanmanČ's Avatar
    Join Date
    Dec 2005
    Location
    Abbotsford, BC
    Posts
    44,167

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    Because its right here in the TIII section, lol. No one checks the KC, but if your here in the TIII section, then you see it,
    1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
    1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
    2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
    2004 GSW TDI, 5 speed, fully loaded, modified.

    Aurora ignition wires for sale. Link to info

    Super60 roller cams or custom/billet cams. Link to info

  15. #15
    Garrett booster Turbo Mopar Contributor
    Join Date
    Sep 2011
    Location
    Newton, MA
    Posts
    65

    Re: Alternate parts thread-OEM to aftermarket-post findings!

    At least on my car (1992 Spirit R/T), the power steering pump is NOT Cardone 20-863 firm feel steering - that unit is a Saginaw rebuild, not a ZF. It is Cardone 2040887 (or any of the other part numbers listed on RockAuto), which is unfortunately quite a lot more expensive and also requires sending in the original pump to be rebuilt. I don't know whether Gates 350390 is the correct power steering pump rebuild kit, but I suspect it is, since it's listed on RockAuto as well - so far, for me, RockAuto's been pretty good about getting TIII parts correct (unlike some other suppliers).

    EDIT: Well, turns out that Gates 350390 is for the Saginaw, not the ZF. I'll post up the right P/N when I find it.
    Last edited by BaxterStockman; 02-16-2012 at 03:39 PM.

Similar Threads

  1. I should post my own thread....
    By Bozo in forum The Original "Turbo Dodge" Cars
    Replies: 22
    Last Post: 03-26-2008, 08:40 PM
  2. Replies: 30
    Last Post: 06-01-2007, 03:40 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •