change of plans, NEW performance parts, Lots of used stuff too

[Murphy]

My original plan was to turbo a TBI spirit, but then I found Shelby Z, so my plans changed just slightly

NEW STUFF:
Walbro 255 fuel pump(90+) - $100
Fidanza round tooth adjustable cam gear - $100
All 4 rotors for a Spirit R/T - $50/pair
HAWK front pads for a Spirit R/T - $50
Turbo rebuild kit from turbocity.com - $75
Dynomax 'over the axle' pipe 2" to 2.25" - $10
TU's Street and strip clutch disc, large spline - $125

USED STUFF:
AA body turbo wiring harness(complete, some oddities, but I cant remember what exactly ATM) - $150
2.5" quazi DP(forget what it stars as) - $10
4 stock 87 2.2 t2 pistons, ~100k miles - $50
t2 top end - assembled, head, manifolds(1pc), turbo(minimal shaftplay), no injectors or TB, ~100k miles - $125
87 t2 block, bad crank - $50
solid rear axle, setup for solid rear brakes, no calipers/rotors - $50
'TURBO' badges, 6 total - $2 each or 10 for the set
A568 Large Spline, was told it was rebuild about 1500 miles before I got it. I pulled off the diff cover to install a LSD, but never did and just put it back together, never used by me - $500
t3/t4 turbo 50 trim stage 2 .63a/r - was told it was run for about 50 miles, never run by me, has some shaft play, has Z bracket, but no WG or SV - $500

Things I want to buy/trade for
Walbro 255 for an 87
Square tooth adj cam gear
Short throw shifter for a 555(piviot point moved style, not chopped)

Thinks I might be able to work out a trade with
Tires - 225/55R15, bare or on rims
6.5" crabs, black center, polished lip
nice aftermarket speakers for a tona
s60 turbo
Koni's/ebachi's for a Shelby Z

Prices do not include shipping. Parts are located in Baltimore City, MD. Would prefer to deliver to SDAC or Carlisle.

Do not hesitate to contact me about anything. Accepting offers. I can take pictures of anything. PM me here or IM/email at onionhedd@hotmail.com

[WOP'R]

im interested in your walbro and TU clutch..

only question i have is, are you selling the whole clutch kit that TU sells or just the disc itself? if so does TU offer the pressure plate TO bearing and alignment tool?

[Murphy]

Its just the disc, I used the plate and TOB in my daytona. I can include the alignment tool. I see the plate on his site. I'm sure he would sell you a TOB if you ask, or you could just get one from your local place.

plate:
http://turbosunleashed.com/shop/prod...roducts_id=305

[BadAssPerformance]

A568 Large Spline, was told it was rebuild about 1500 miles before I got it. I pulled off the diff cover to install a LSD, but never did and just put it back together, never used by me - $500

Got pics to e-mail me? especially of the gears inside?

Thanks,

[WOP'R]

is the disk cerimac or kevlar? 4 puck or 6?

[Murphy]

Its kevlar.

BAP, i put the cover back on but i can pop it off again and snap some pics. I didn't RTV it or measure anything since i was planning on sending it off to have the OBX put in

[BadAssPerformance]

Actually I wanted to see the actual gears that are visible when the shifter housing is off the top of it....

[shelby zed]

if the pads will fit an 88 shelby zed ill take them

[shelby zed]

oh and the dp possibly pending pics

[Murphy]

I dont think the pads will fit a shelby Z, and the DP is sold

sorry I need to update my thread on whats sold/pending

[inplansight]

Are you willing to sell just the turbo ?
paul B

[Murphy]

off the t2 top end? that is sold sorry

heres my update on sold/pending

SOLD:
Walbro 255 fuel pump(90+) - $100
TU's Street and strip clutch disc, large spline - $125
2.5" quazi DP(forget what it stars as) - $10
Turbo from t2 top end


Pending:
A568 Large Spline, was told it was rebuild about 1500 miles before I got it. I pulled off the diff cover to install a LSD, but never did and just put it back together, never used by me - $500