How many teeth are on the diff ring gear and also on the main shaft it meshes with?
Thanks in advance.
How many teeth are on the diff ring gear and also on the main shaft it meshes with?
Thanks in advance.
Last edited by Gaboon; 06-07-2007 at 09:43 PM.
What gear ratio?
1989 FWD Turbo Caravan-2.5 TIII, GT35R, auto, a/c, cruise, pwr windows/locks, fully loaded with interior and ran with full exhaust. RETIRED FOR A FEW YEARS! 12.57@104 :O)
1984 Chev Getaway van, 6.2 Diesel with a remote mounted turbo setup burning WMO-For sale.
2003 GSW 2.0L TDI, auto, fully loaded, modified, 360K-wife's.
2004 GSW TDI, 5 speed, fully loaded, modified.
Aurora ignition wires for sale. Link to info
Super60 roller cams or custom/billet cams. Link to info
I beleive either 3.50 or 3.55?
Going to put this stuff in my A555
I'm getting the stuff from the tranny shop near my house. He's at this time pressing the bearings on my OBX LSD and told me he had the ring gear and shaft from an A520 that I was looking for.
I want to make sure it's the right stuff when I pick it up tomorrow.
If you have the parts, count the teeth and divide the ring gear teeth by teh pinion teeth. If they are A520 gears the result will either be 3.50 or 3.77 or 3.85...
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
No problem... btw, the 3.50 is the way to go
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
That's what I'm looking for.
With the 3:85 ratio I have in there now, I was spinning to just under 7000 rpm in 4th at the end of the 1/4 mile with 23 inch slicks....
My car did the same thing on a shitty track the first time I tried spray on it. Apparently the track didnt VHT that far down the lanes... i was never sure if it was one or two tires spinning (open diff).
Regardless, it sounds like OBX / 3:50 gear might help then... if it dont, then you need some bigger slicks
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
Just picked up the diff, ring and pinion. 49 teeth on the ring gear and 14 on the pinion...= 3.50 got the right one!
Thanks!
Sweet! You gonna have it at SDAC-17?
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.
Sadly, I don't think the car will be ready. I'm rebuilding the engine completely and upgrading some stuff as well. Some of what I ordered was back ordered and is only due to be received sometime next week. I still need to get the block to the machinist and haven't been able to because I'm missing a crutial item( what I'll be receiving next week)
The head it ready, tranny will be ready this weekend and as soon as the block is machined, I'll be able to assemble it quickly and get everything back in the car. Then there's the detailing...... that takes me a few days LOL...
I'm going to try and get to SDAC anyway, I'm trying to persuade crazy1eye to bring his car. If not I still might make it for a few days to hang out with the boys.
Looking forward to it!
Well I'm not going to have my Z their either, but will have my Shadow at least!
Yeah, talk Pat into bringing his car, or bring Kenny's green one
JT
SDAC Director
SDAC-Chicago President
JOIN SDAC and your local Chapter TODAY! - SUPPORT the CLUB that supports YOUR HOBBY!
87 Shelby Z - 10.50@141.66mph
87 CSX #751 Clone - 12.88@102.88mph
www.badassperformance.com
Check out Turbo-Mopar Times!
Submit your 1/4 mile times HERE!!
Support SDAC! Join Today!
"I'm not some pro athlete with a bajillion dollars, I'm just an every man"
Note: The information and any images provided in this post are not for distribution outside this forum without the author's permission.