Search:

Type: Posts; User: Dr. Johny Dodge; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. For Sale Re: Repost FS: 1989 Chrysler LeBaron GTC Turbo II 5spd Convertible

    there's a black lebaron convert parked in a driveway not far from me.. been there since 2000-ish
    large expensive in it's day house .. so the car ain't yard trash ..
    THAT's probably the guy who...
  2. Replies
    88
    Views
    5,133

    Re: Difficult Ignition Cutout Problem

    have you tried changing the power module?

    a glitch..is how I would describe my 87 shelby z..or a ghost as I later swapped the known "glitchy" 87 lm/pm TII deal into my turbo z
    and yep the glitch...
  3. Replies
    88
    Views
    5,133

    Re: Difficult Ignition Cutout Problem

    ment to ask before ..you mentioned the water temp sensor sometimes throws a code when your issue happens..
    what about checking the splice at the firewall for the sensor grounds ?

    all the black...
  4. Replies
    88
    Views
    5,133

    Re: Difficult Ignition Cutout Problem

    I've seen odd job splices like that one before
    I think it's where they ran out of wire on the roll and started a new roll of wire while creating the harness

    more cost effective than throwing...
  5. Replies
    351
    Views
    118,920

    Re: 1986 Shelby Charger Saved from the JY!

    mm
    first thing..pull end of vac line to regulator ..sniff to see if it smells like gas..

    regulator might have started retirement without notice..

    and it's the easiest part to replace so..hope...
  6. Replies
    88
    Views
    5,133

    Re: Difficult Ignition Cutout Problem

    "I only rant for a few moments, but all was quiet on the western front."

    LOL

    best chuckle I've had since I got my computer back online
  7. Re: L-Body Drums - Where can you buy them?

    only Chrysler sold drums with hubs pre-installed
    and
    you need to know BEFORE you start trying to knock stuff apart..
    Chrysler "swedged" the studs.. this means the shank of the stud gets hit with...
  8. Replies
    5
    Views
    1,067

    Engine Re: Log Intake & Heat Shield bolts

    if it's one of the two bolts at the passenger side .. you don't need to worry about it
    if it's the one bolt at the driver's side then a zip tie might be good enough to hold the heat shield up off...
  9. Replies
    22
    Views
    1,369

    Re: Odd spark plug behavour

    do you have the support bracket/bar that attaches to the head and neck of the 2 piece intake in place?
    that bar stops false knock readings from happening
    that's why it's there .. it's not a support...
  10. Replies
    24
    Views
    1,592

    Re: Excessive oil consumption

    5 quarts ..I'm presuming you've removed the balance shafts

    I had cam seal issues with mine when I went from 2.2 to 2.5 without knowing to only put 4 liters in the 2.5 ..with shafts

    kept...
  11. Replies
    24
    Views
    1,592

    Re: Excessive oil consumption

    was the oil filter full when you checked the oil level ?

    if it was new or had sat for some time without running ..maybe you never lost anything (?)
  12. Replies
    24
    Views
    1,592

    Re: Excessive oil consumption

    if it were leaking from the hot side it should produce traffic stopping clouds of smoke
  13. Replies
    24
    Views
    1,592

    Re: Excessive oil consumption

    I presume you're running an intercooler
    that's the spot the oil from the pvc usually accumulates ..bottom tank

    if you're missing a quart a catch pan below the hose might be wise before you...
  14. Replies
    24
    Views
    1,592

    Re: Excessive oil consumption

    firstly.. crankcase operating in vacuum is a very very good thing.. it promotes ring sealing to both the cylinder wall and the lands of the piston

    (this might be the reason our stock crankcase...
  15. Replies
    16
    Views
    1,129

    Re: 1985 New Yorker No spark

    I'm pretty sure your omni LM ain't gonna work in a K car

    L body vs g body was unique to body line and to add regardless an 85 lm would not work in an 86-7 ..not without changing distributors

    my...
  16. Replies
    31
    Views
    1,975

    Re: High amp alternator wiring

    does it cut out when just driving or does it happen when you step into it?

    had a daytona with a cut out .. took a couple of months after getting the car to find the coil wire terminal in the coil...
  17. Replies
    5
    Views
    483

    Suspension Re: 91+ knuckles

    don't forget you likely will need the larger diameter late model balljoint pinch bolts and nuts...!!
  18. Replies
    12
    Views
    704

    Re: Power brake bleeder

    simple solution is"RUSSEL" brake bleed nipples.. they work one way so you can bleed brakes by yourself
    you'll have to figure out the correct ones to fit hole & thread
    ...
  19. Replies
    53
    Views
    5,041

    Re: NHRA check list for Stock Eliminator

    how badly do you wanna nice transmission?

    NEVER been in a car..nos 588 EURO trans

    3:69 first gear
    4:08 final drive

    also brand new in box Quafie LS diff

    comes with nos shift cables and a...
  20. Engine Re: Billet Short Stroke Common Block Crankshaft

    I just hope we see somethin special come of it
    there haven't been any big new projects 'round here for a while..
  21. Engine Re: Billet Short Stroke Common Block Crankshaft

    posted as sold under pic in first post ..
    .......................................................


    Crankshaft has been sold.



    Last edited by BadFastGTC; 06-04-2022 at 03:54 PM.
  22. Replies
    259
    Views
    161,982

    Sticky: Re: Connectors

    that looks like a good option ^

    message back on ebay was no sorry that's all he has
  23. Replies
    259
    Views
    161,982

    Sticky: Re: Connectors

    I just sent this seller a message asking if he has a female connector the one he has listed could plug into
    ...
  24. Replies
    259
    Views
    161,982

    Sticky: Re: Connectors

    AH,..OK,you left out the bit about replacing it with the one piece manifold..
  25. Replies
    11
    Views
    791

    Re: TII Rad Replacement

    well worst case, leaking tubes can be soldered shut easily enough , though it would be nice to have a better core ..at that point too but .. sometimes "you hafta work wit whatcha got"
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4