http://i.ebayimg.com/00/s/NDgwWDY0MA==/$(KGrHqF,!o8F!YCD3ssIBQQT+bh(fw~~48_20.JPG
http://london.kijiji.ca/c-ViewAdLargeImage?AdId=407151589
Type: Posts; User: 87turbodance; Keyword(s):
http://i.ebayimg.com/00/s/NDgwWDY0MA==/$(KGrHqF,!o8F!YCD3ssIBQQT+bh(fw~~48_20.JPG
http://london.kijiji.ca/c-ViewAdLargeImage?AdId=407151589
I ended up putting some extra o-rings around the bottom of my GM pencil injectors to prevent them from going too far into the lower intake. Worked well with no leaks and the rail held the injectors...
If you just cut the old hoses off with a pipe cutter you could slide fuel injection hose on BUT be sure to expand the end of the steel line with something like a flare tool to prevent the hose of...
I might look into that. I need to do some fine tuning. I just quickly overclocked it when I setup this pc in march. It's in a htpc case and attached to my tv for gaming.
I'm running 2400mhz... nb and ht I think. I'm using my laptop right now so I can't check.
Only things I've changed are the Vcore, multiplier and bus speed. I'm not sure what the HT multiplier is set at but I must have lowered it when I raised the bus speed. I'm running 250 bus speed...
I have a 6850 as well in my PC and a phenom2 x4 955 at 4ghz and I have been able to play any new game on high so far.
http://img192.imageshack.us/img192/2396/dscf0646w.jpg
http://img685.imageshack.us/img685/1183/dscf0648i.jpg
http://img802.imageshack.us/img802/2532/dscf0649.jpg...
I set up everything with the trans sitting in neutral then position the shifter where I wanted it in neutral, verified I has sufficient travel in each direction and welded. I did this because it was...
I didn't put any pins in but... I did weld the drivers side cable bracket in a custom spot to fit a neon cable instead of a K car cable - works awesome. I'll post a couple pictures in a couple...
What neon cable do you have installed now? The selector? In my experience the neon crossover cable is usually way too short.
There is only some adjustment for the crossover cable not the...
I'm not sure on the differences between neon shifter cables over the years but I have 2001 Neon cables in my Spirit. I modded the cable bracket on the trans slightly to make it work. I actually...
Don't make the ports too smooth or that will hurt flow kind of the way a golf ball flys further beause of the simples on the outside of it.
I use box.net to upload Ms files.
If going with the crank sensor for wasted spark, you may need to to make some minor mods to the tach input ciruit on the MS. You can choose to use a hall-effect or make a different wiring change...
More dwell may help but it's hard to tell how much dwell is just enough without a scope. Once the coil becomes saturated and addition dwell will just be turned into heat by the current limiting in...
I just thought I'd throw the idea out there since it's not too difficult to do if you have some time and junk yard nearby. Two BIP373 coil driver kits would be required from diyautotune as well.
I think it's time to go wasted spark! Make a toothed wheel on your crank like I did and then you can run some cheap wasted spark coils from the junk yard to begin with. Cheap and easy!! You...
At TDC on cyl 1 you want the rotor to be just about to leave the terminal in the cap for cyl 1.
Go for it! I'd get the BPR8ES-11 though.
According to the NGK website the stock 3.0 plug is: BPR5ES-11
The turbo 3000GT uses a BKR6ES-11 so basically one step colder then the 12V 3.0.
The 3SI guys seem to recommend something two steps...
Are your valve covers leaking?
Interesting. Good to know. I'm guessing the 80% number is just a safety factory then in case you need more fuel then 100% can give.
The duty cycle of the injectors is the duty cycle and has nothing to do with injector size settings in MS. I was trying to say above that the injector size you enter in MS is only used to estimate...