Search:

Type: Posts; User: rosie; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    1,712

    Re: Omni with 2.2 turbo engine codes woes

    You 100% on the O2 sensor?


    Were you welding on the car by chance? Working near the passenger floor?
    The logic module is in the passenger side kick panel if you have the set up I think you do....
  2. Replies
    22
    Views
    1,712

    Re: Omni with 2.2 turbo engine codes woes

    Anyone helping you out yet?
  3. Re: SBEC Electronic schematic/flowchart/logic diagrams

    Thanks for the reply @chromguy
    I've also got a computer code and an inop ASD signal. 2 different SBECs. I'll start a thread eventually.
    Figured the voltage regulator would be the easiest path to...
  4. Re: SBEC Electronic schematic/flowchart/logic diagrams

    Thanks for the reply but the search continues then.

    Same question, anyone have the schematics?
  5. SBEC Electronic schematic/flowchart/logic diagrams

    Greetings,

    Where would the conversation for component level repair of an SBEC start?

    All the CLR I do at work I have prints to work off of and it hasn't been until recent that I've run into bad...
  6. Replies
    6
    Views
    5,716

    Re: San Diego work party Jan 20th

    So johns out and JT isnít going to make it either but invite is very much active.

    Playoffs will be on in the garage as well.

    Theres a arm drop race at the drags the weekend after. Want to...
  7. Replies
    6
    Views
    5,716

    Re: San Diego work party Jan 20th

    Johnl, sorry to hear that man. Hope all is well. You were on the direct call list Iíve just been busy.

    AJ, beer is always free at my house.
  8. Replies
    6
    Views
    5,716

    San Diego work party Jan 20th

    Sup guys,
    Long time no see,

    Putting it out there if anyone would like to come down and hang out, (I think @csdaytona) Louis and I will be doing a head pull turbo swap on his Daytona CS. Invite is...
  9. Replies
    15
    Views
    6,317

    For Sale Re: 87 Shelby Charger GLHS #232

    Email sent
  10. Replies
    5
    Views
    709

    Re: 89 to 90 engine swap, what did I miss?!

    Yeah, loaned it to a girlfriend and forgot to tell her 91 octane.
    :foreheadslap
  11. Replies
    9
    Views
    2,399

    Re: 1989 Shelby Ram conversion van? WTF

    Ad said a hundo. Might need some shelby geek to dig deeper on that number
  12. Replies
    5
    Views
    709

    Re: 89 to 90 engine swap, what did I miss?!

    Complacency is the mother of all goof ups. I used the arrow instead of the dot for TDC on crank. Genius

    Thanks er' body
  13. Replies
    5
    Views
    709

    89 to 90 engine swap, what did I miss?!

    I got fuel, spark, and compression but it won't fire up. I've set a million timing belts and obviously going to re check that but is there something I'm missing? Like does the smec not like an engine...
  14. Replies
    9
    Views
    2,399

    Re: 1989 Shelby Ram conversion van? WTF

    Oh snap! That's down the street!

    I saw outside the junkyard one time, left my info on his windshield but he never called back!

    I'm car rich right now in the process of selling them off so if...
  15. Replies
    20
    Views
    2,977

    Re: What got me hooked on fwd mopars!

    Getting into these cars is another story, but as far as getting hooked?Found sdml and met a guy who taught me how to work on cars. I was already mechanically inclined but a head gasket was as far as...
  16. Replies
    17
    Views
    2,798

    Re: how do i remove bearing pieces from oil pan?

    Trying to add pic with an ancient 2yo droidX.
    If this doesn't work, I'll be back.
    If it did.
    LOOK AT ALL THAT CRAP!

    Finding that stuff killed my ignorance and I'll never be able to NOT not do...
  17. Replies
    17
    Views
    2,798

    Re: how do i remove bearing pieces from oil pan?

    I took off an oil pan yesterday because I was doing the rear main on a beautiful junkyard engine that had a leak on the.... rear main.

    Found some grit on the pan floor and noticed the pick up was...
  18. Replies
    771
    Views
    93,744

    Re: SoCal SD/TD/FWD Chrysler Meeting time again...

    Wow! A reschedule?! First ever???
  19. Replies
    6
    Views
    1,142

    General Re: Wanted: Lancer/Lebaron GTS DS fender

    Just a bump to see if one popped up while I was sleeping.
  20. Replies
    3
    Views
    1,007

    Shelby Lancer #606

    My first T-M was a 87 Lebaron GTS 15 years ago. My first internet search (pre google of course) on the car resulted in the discover of the Shelby Lancer. Since then I've always wanted one and can...
  21. Replies
    5
    Views
    772

    Re: Back cut on +1 stainless?

    All good mike. I asked about you :)

    Thanks for the bump

    I'm hoping someone who's used these valves will chime in
  22. Replies
    5
    Views
    772

    Back cut on +1 stainless?

    Is there any gains to be had to put a back cut on the stainless +1 valves from TU?

    THANKS
    Rosie
  23. Engine Re: 2.5 forged pistons, rods, CB, bearings, lancer headlight covers, rings

    And shipped fast as hell. Got my lenses today. I was wondering when I was going to hear from you about shipping them and BAM!

    Hope they're in good shape (Haven't opened the box yet).

    :)...
  24. Replies
    51
    Views
    5,719

    Re: my $100 89 Lancer Shelby... + a trip to NJ

    Congrats! Second favorite H body!
  25. Replies
    6
    Views
    1,142

    General Re: Wanted: Lancer/Lebaron GTS DS fender

    Bummer.
    Anyone else want to ship me a fender?
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4