I forgot I was already in on this lol
Carry on 🤣😂🤣
Sent from my iPhone using Tapatalk
Type: Posts; User: knownenemy; Keyword(s):
I forgot I was already in on this lol
Carry on 🤣😂🤣
Sent from my iPhone using Tapatalk
FYI: I screenshot your response and sent it directly to my machinist in a txt.
Thanks man! 🤘🏻
Sent from my iPhone using Tapatalk
Comp springs are exactly what I’m running.
I’ll forward this information to him.
Thank you. 👍🏻
Sent from my iPhone using Tapatalk
Ok, I understand there hasn’t been much action in this thread in a bit, but I have a question from my machinist who’s setting up my head for the R5 cam...
Spring loads? And requirements? 🤷🏼-♂️...
I’m in for 2!!!(SMEC)
I have to go back and read the entire thread for payment details if they’ve been outlined.
FWIW: This is outstanding!!!
1. Cordes
SMEC, S, 2
SBEC, S, 1
2. knownenemy...
I didn’t consider the over the V/C T/B idea. I saw someone do it somewhere, can’t remember who.
With the HE351CW, 70mm T/B, and 3” mandrel elbow I should be able to get enough air in there that...
Here’s the hemispheres I attached to the ends of mine.
https://uploads.tapatalk-cdn.com/20200514/051390ed8b20fbad07b8bc2392636285.jpg
Sent from my iPhone using Tapatalk
Are you running ALKY injection?
If not, it would really help keep the AIT down.
The whole setup looks awesome!!! 🤘🏻
Sent from my iPhone using Tapatalk
Won’t this shield trap the heat around the intake runners?
It’ll help keep the fuel rail cooler, but at the cost of heating the air in the runners, no?
Don’t get me wrong, I like it, and I intend...
I’m in for 50.
Let me know when/how I pay.
Thank you. 👍🏻
Sent from my iPhone using Tapatalk
I actually acquired seats literally minutes after starting this thread. 😃
Sent from my iPhone using Tapatalk
Tried PMing you my shipping info, but it says your inbox is full, and you can’t receive any new messages until clearing out some old ones.
Sent from my iPhone using Tapatalk
The numbers appear to be correct for the application.
If you would, PM me a shipped price.
Thanks for the quick reply. 👍🏻
Sent from my iPhone using Tapatalk
Looking for G-Head Big valve seats(44mm int/38mm exh)
My cylinder head is already at the machinist. So, the sooner the better. 😃
I’ve been looking around the inter-webs and read in a couple...
Assembling the case? 🤷🏼-♂️
It’s been almost 2yrs since the MPSciLink arrived at my doorstep. I’m finally getting around to assembly and I can’t find instructions anywhere. Are they posted somewhere,...
I’m searching for a set(4 intake/4exhaust) of the MP G-head IMSA valves.
-OR-
If anyone is aware of an equivalent out there somewhere, please let me know.
Thanks, in advance. 👍🏻
Sent from...
I’ll have to reach out to them. Thanks.
Sent from my iPhone using Tapatalk
You read that right, I’m looking for a 655 casting cylinder head.
If all you have is the casting itself that’s fine, but if it’s got valves and all that’s ok, I intend to replace them anyway.
Let...
I have AllData, but the pinout for the SOHC MASI isn’t there. There is one for the DOHC engine MASI, but I can’t be sure they’re the same.
Can anyone that has access to the bulkhead pinout for the...
Man, that’s terrible.
I build harnesses, and I have AllData, but the diagrams for the 89 TC by Maserati SOHC(T2) book is extremely limited (no bulkhead pinout or anything)
The DOHC bulkhead is in...
Any further updates?
I use an iPhone as my primary, and it would be really great if I could also use it with MPtune & Scandroid.
However, I do have an Android specifically for tuning etc.
I believe so, but I’m going to make a support bracket anyway. I’ll be using a 3” elbow and a 70mm T/B
Sent from my iPhone using Tapatalk
Pressurized the intake to line pressure of 125psi; no issues 🤷🏼-♂️
Sent from my iPhone using Tapatalk
The 5” hemispheres were quite affordable from a manufacturer called “fat daddio’s” at Amazon.
Shadow and I both had this idea. I believe we discussed it in the BMF R&D thread waaaay back when.
...