The site says that 1.5" should be subtracted for each hiem joint. Since the current center to center on the track bar is 46" then a 43" bar would be correct with room for adjustment. The current...
Type: Posts; User: dr_amx; Keyword(s):
The site says that 1.5" should be subtracted for each hiem joint. Since the current center to center on the track bar is 46" then a 43" bar would be correct with room for adjustment. The current...
This is still a good parts list at speedway for anyone else wondering. I will also buy a similar setup for the panhard bar. Thanks for all your help!
Part number list:
910355-42.....Aluminum...
I installed the exhaust and I did no massaging. The bolt if from a exhaust previous to my ownership.
I wonder what to do then. Maybe I should try partially boxing the panhard and mount to see if...
So I have been thinking about this. If my track bar was bent then the axle would be justified to the drivers side. It must be the trackbar mount or the static panhard bar that is bent for it to move...
Thanks, that is good info. I think I am going to go with something approximating the poly bushing solution "track bar made with 7/8" DOM, 0.156 wall steel tubing." If I order the correct left hand...
Does anyone have a picture or specs on what the CSRacing panhard bar looked like? It appears that I will need to make a bracket for the body side and then decide how to change the interface of the...
Do you (or anyone) know if there are any springs available still that will work? I have a full set of KYB struts/shocks I will be installing. Not good stuff I know but better then the 140k stuff that...
My car has stock spring to the best of my knowledge. I suppose a fella could chop the bar and take out the offset needed and weld it back up.
Hello,
I am looking for help on solving my offset rear axle on the Spirit R/T. I picked up some new 225/50/16's for the car and now I am really rubbing on cloverleafs. It had 205/55/16 on the rear...
"The higher the number, the more lean you are running." That makes me feel better. Guess I need more boost, lol. Thanks!
Oh, I was thinking that 14 was the safe spot. I guess I have it backwards. The Innovate AF gauge reads constantly. I was watching it as I accelerate so part throttle not WOT.
I finally got around to changing the regulator. I set the pressure back to about 44psi without the vacuum line. I also put in a new AFR. The AFR is going down to 11-10 when in a little boost. Do I...
Well I believe I have found the grey connector which the wire enters and does not exit. Are pins still available for these connector or is a bone yard my only hope?
Hi All,
As the title says my reverse light connector and wiring are missing. I have pulled back most off the covering on the wiring around the battery area and I am not finding signs of it...
Thanks again Todd!
Ben
Here is why I asked the question about the fitting and the o-ring position. http://www.fwdperformance.com/Store/Product.asp?IDCatalog=7&ProductID=859 (Name: Fuel Fittings for Universal Regulator Part...
Thanks!
Ben
Measured the fuel pressure last night. 42psi. The AccuFab also showed up but I still need to order some fittings. How thick do these washers need to be? With the 14mm adapter, is the o-ring near the...
I don't know the current fuel pressure. I will have to check. Since you guys have verified that the accufab works on a stock rail I will likely do that. Lots of little things to cleanup on this car....
Is it possible to put a stock FPR back on the car and let the CPU handle the tune? Or am I already out of the range of a stocker at this point?
TIII
-57 trim T3/T4 Turbo from FWDperformance
-FWD...
Sorry All,
For some reason I did not get the notifications that there were replies here. The application is a 1991 Spirit R/T. The 772 is the only part number I can see on the top side of the...
HI all,
I am looking for a replacement for the Bosch 772 manual fuel pressure regulator. I could go the FWD performance route of a new regulator and fuel rail but I am wondering if there is a...
Date: 23rd July 2018
Username: dr_amx
Full Name: Ben Kjellberg
City, State, Zip: Mounds View, MN, 55112
Contact: madmodifier@gmail.com
Selling or Wanted Price: $4000 pretty firm (trade for a...
Are you guys going to have cars in the show? I have thought about going Saturday but I will park my spirit in the spectator lot.
Yeah I noticed your avatar. It looks sweet. Hope that I will see your X some day if I have not already. Are you going to the nationals in Kenosha?