Search:

Type: Posts; User: cordes; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.13 seconds.

  1. Thread: Connectors

    by cordes
    Replies
    204
    Views
    55,533

    Sticky: Re: Connectors

    I'm in for some.
  2. Thread: WTB: 87 LMs

    by cordes
    Replies
    23
    Views
    714

    Electronics Re: WTB: 87 LMs

    The chip in the last board that died was a SST27SF512. I socketed one of the new to me LMs, installed the same chip and the car now has hundreds of relatively trouble free miles on it. I think I'm...
  3. Replies
    2
    Views
    64

    Re: 87 Turbo 1 engine rebuild and upgrade

    There's not much to it. Just a couple manifolds, compressor cover, TB, throttle cable, and the associated plumbing for the most part. You have to look out for some things like the fact that if you...
  4. Re: Sudden Extreme Fuel Usage And Down on Power

    A bad map or vac signal to it can cause extreme fuel use. The plugs should easily tell the tale. A plugged cat will make it down on power, but I don't think your fuel mileage should suffer much from...
  5. Re: Sudden Extreme Fuel Usage And Down on Power

    There's no cooler way to do it than DDing an 87 NYer.

    Do you think the timing belt could have jumped a tooth? I would pull the plugs and see what they look like too. There's no way you're not...
  6. Replies
    3
    Views
    107

    Re: 05 Neon ATX No Start

    Well, I'm happy that I have some age and experience under my belt today. I don't like to throw parts at things, but I replaced the coil in the car because the spark looked a little weak. The plugs...
  7. Replies
    3
    Views
    107

    Re: 05 Neon ATX No Start

    I've replaced my cam sensor a couple times now, but it's always thrown a code. I'll report back tomorrow after I check for spark and fuel at the injectors. The closest thing I could find to this so...
  8. Replies
    3
    Views
    107

    05 Neon ATX No Start

    My wife's 05 Neon wouldn't start tonight. It turns over just fine and I can hear the FP priming in a normal fashion. I only get a code 0522, which is not surprising since the low oil light will come...
  9. Replies
    6
    Views
    169

    Re: SMEC tbi to turbo

    I've never heard of the former, but people on the board are currently working on using the V6 SBECs for 4cyl turbo applications.
  10. Replies
    9
    Views
    233

    Re: 85 L-body Connector ID

    5 a. is the horn if I'm not mistaken, while B is the diagnostic connector. The fuse looking things are for the solenoids.

    4 I think is AC stuff.

    I think 3 a is where the TPS and AIS plug...
  11. Re: Gauging interest in a new high capacity LM/SMEC/SBEC/SBEC2 flash module

    So, does this just flash the stock board? I would probably be interested in that.
  12. Re: Gauging interest in a new high capacity LM/SMEC/SBEC/SBEC2 flash module

    I just want to use a flashable chip which I can burn with my Burn2 and call it a day for the most part. I generally make the hardware changes to the engine, get the cal right, and forget it on my...
  13. Replies
    7
    Views
    286

    Re: 2.5 Inch Exhaust Upgrade

    A 3" DP fits a 2.5" SV pretty well. I've done that myself. I've never tried to put a 2.5" DP in a 2.25" SV, but I'm sure it would work just fine. A better option would be to find a 2.5" or even 3" DP...
  14. Replies
    7
    Views
    286

    Re: 2.5 Inch Exhaust Upgrade

    Welcome to the site!

    There will probably be some tweaking necessary for any exhaust kit you want to put on it, but it should be no problem for a good shop. Your turbo has a tiny 2.25" swing...
  15. Replies
    10
    Views
    300

    Re: 87 csx Lm pinouts needed

    Is it the black with blue tracer wire? Those have splices in them all over since it's the ground used for almost all the sensors.
  16. Replies
    9
    Views
    470

    Re: Decent price for chrysler laser?

    That could be. I thought everything was rod shifted up until 83 or 84.
  17. Replies
    9
    Views
    470

    Re: Decent price for chrysler laser?

    Sounds like a $500 car to me. Gas in the oil could be any number of problems. Bad FPR, bad injector, wiring problem, etc. etc. Was it the digital cluster? I'm not an expert on the 84 Laser, but I'm...
  18. Replies
    9
    Views
    470

    Re: Decent price for chrysler laser?

    I would tend to agree. There is so much on the 84 cars that's 84 specific I don't think I would be up to own one, but that's me. Heck, didn't the 84s still have the pivot point for the shift linkage...
  19. Replies
    6
    Views
    215

    Re: Different part numbers the SBEC2 PCB board

    If you have one which is fairly clear, you should be able to read what is under the potting compound. IIRC, the numbers are toward the outside of the board and not obscured by components.
  20. Re: There are two very different SBEC2 PCB---Wow are they different

    Tag for exciting news. I really appreciate you spear heading this. The idea of being able to use a v6 computer is incredible. Not only should they be a decent upgrade to the 84 to 89 stuff, but...
  21. Thread: Out of Business

    by cordes
    Replies
    8
    Views
    10,340

    Re: Out of Business

    Glad to hear they're back up and running. I liked the product I received from them years ago.
  22. Thread: Csx vnt #497

    by cordes
    Replies
    12
    Views
    4,125

    Re: Csx vnt #497

    The CSX is sitting out front dripping used motor oil all over the place. I filled up a sprayer and went to town with about 1.5gal of the stuff. I sprayed it in the doors, under the car, under the...
  23. Replies
    0
    Views
    198

    Positive kuzman83 Good Seller

    Good seller. Thanks a ton.
  24. Replies
    4
    Views
    286

    Re: Resource message

    That's a good question. It happens to me also.
  25. Thread: Csx vnt #497

    by cordes
    Replies
    12
    Views
    4,125

    Re: Csx vnt #497

    I finished off a lot of maintenance yesterday. I replaced both rear wheel bearings, and the shocks. That was fun due to the rust. I sprayed everything very well with Fluid Film. I replaced the...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4