Search:

Type: Posts; User: 4 l-bodies; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    24
    Views
    635

    Re: Super 60 Wire Harness Help

    Ryan,
    Well good thing you bolted in a 87 and older dash harness (lol)
    You can use any 88 harness for parts, but they're all fairly unique for each chassis. The 88 alternator harness out of a 88...
  2. Replies
    24
    Views
    635

    Re: Super 60 Wire Harness Help

    Ryan, a 88 alternator harness from a l-body will work, but you would have to graft in the turbo HEP wiring into it. A 88 alternator harness from a larger turbo will be a complete plug in. On some of...
  3. Replies
    7
    Views
    247

    Re: Heater Bypass Valves

    Why don't you just bypass the bypass valve? That is exactly what Chrysler did by the mid 90's. My AC works just fine without the bypass valve installed. I tired of them leaking all the time too. My...
  4. Replies
    24
    Views
    635

    Re: Super 60 Wire Harness Help

    Harry, Thanks for posting that. The reason I mentioned the detonation sensor wiring snafu is OP is NOT using s-60 SMEC, only the wiring. He merely wants to update l-body wiring to SMEC from original...
  5. Replies
    24
    Views
    635

    Re: Super 60 Wire Harness Help

    The s-60 harness was based on the 88 l-body harness. MP grafted in the MPFI wiring, and used the 40 pin connector on the bulkhead connector so it would plug in to any 85-87 turbo L-body. As...
  6. Replies
    24
    Views
    635

    Re: Super 60 Wire Harness Help

    Well I agree but the S-60 SMEC you had the ability to switch via toggle switch from 92 octane to 100+ octane hi boost aggressive spark. Lots of people weren't that happy with the tune when it came...
  7. Replies
    33
    Views
    1,201

    Re: Opinions on Turbo for Spirit R/T

    Yes, Gen II Garrett GTX series flows like 20% more than Gen 1. So a GTX3071R will flow about the same as a GTX3076R Gen 1. Just spools up about 500 RPM quicker. Some of these Gen II GTX3071's are...
  8. Replies
    33
    Views
    1,201

    Re: Opinions on Turbo for Spirit R/T

    Why are you guys suggesting ball bearing billet turbos when his budget is $800. They're over twice that $.
  9. Replies
    49
    Views
    1,753

    Re: Interchangable LSD

    Wow that didn't take long. It just came to market 2-3 years ago.
  10. Replies
    49
    Views
    1,753

    Re: Interchangable LSD

    Didn't Chris @ TU offer a different than OBX or Quaife LSD option a couple years ago for that application? ...
  11. Replies
    11
    Views
    612

    Re: t-stat bleed screw.. alternate

    Well if its a 3/8ths" NPT, it will fit. Been using one like it for 30 years in my cars. That steel plug in an aluminum head is icky. Stainless plug works too, at least you can get them out. Best best...
  12. Replies
    13
    Views
    725

    Re: HE351 OMNI Which manifold??

    Johny, my thought on that wouldn't it be harder fitting an internal wastegate on it? Seems like the actuator would need to be about where the turbos outlet or charge pipe would be. I agree, it is...
  13. Replies
    13
    Views
    725

    Re: HE351 OMNI Which manifold??

    On my combo this was 2.2 in GLHT with fully ported head, pistons coming out of hole .025 or so, but not any added compression (bigger -22cc dish). S-60 turbo, Taft S2 camshaft, 568 tranny, stock...
  14. Replies
    13
    Views
    725

    Re: HE351 OMNI Which manifold??

    I ran a TBI header for several years with no issues on the oil return. Sorry, mine was S-60 Chrysler bolt pattern. Flame spray welded. I had a fitting drilled into the oil pan. Factory oil drain tube...
  15. Re: 1988 K-car style LeBaron sedan rear wheel cylinder questions.

    I've dropped both a tranny and a bare block on my stomach in the past. Both hurt! The tranny was at a self service car wash down in San Antonio. Had the floor all soaped up and my feet went right out...
  16. Replies
    2
    Views
    221

    Re: Oil leak in turbo van

    If you tear down the belt side of the engine, you should be able to see where the leak is. My bet would be the aux shaft seal or crank seal is bad. The rotating parts, crank sprocket and aux shaft...
  17. Replies
    130
    Views
    24,186

    Re: Head Porting

    Brian,
    Perhaps your issue could have been because the factory guides are gang drilled. In other words the ID of the guide is not concentric with the guides OD. I've never had issues using the 942...
  18. Replies
    11
    Views
    563

    Re: Will this 3Bar Map work?

    Yeah I think I would stay clear of a $20 3 bar MAP. Glad you can appreciate a little humor.:clap:
  19. Re: 1988 K-car style LeBaron sedan rear wheel cylinder questions.

    I kind of thought it was, but didn't want to have you sitting by your PC waiting for me to answer (lol). That actually was my first thought, oh Randy is being funny.
    Good to hear your "back on the...
  20. Replies
    11
    Views
    563

    Re: Will this 3Bar Map work?

    Buy one along with a $125 turbo and crank up the boost by unplugging wastegate actuator and fill with 87 octane and let her rip. :p
  21. Replies
    2
    Views
    172

    General Re: SDAC MidWest Newsletters

    PM sent
  22. Re: 1988 K-car style LeBaron sedan rear wheel cylinder questions.

    Sorry Randy, not getting any update notifications again, so I just stumble onto these threads:(. Glad to hear your making good progress. Brake adjuster hole plug, the rubber plug? They can be a...
  23. Replies
    3
    Views
    218

    Re: Stamped letters on rails

    Yes they were stamped on the rail to determine what size each cylinder bore was, so the correct piston would be used. ABCD were used in production. Letter E was sold by DC/MP performance. Each letter...
  24. Replies
    14
    Views
    687

    Re: Masi 16V clutch/flywheel differences

    Yes Randy I believe they do.
  25. Re: 1988 K-car style LeBaron sedan rear wheel cylinder questions.

    Little FYI, I had the same thought on stocking up. Bought several brake lines from RA for my Shadows and L-bodies. Two lines I got from RA were going bad right in the box! The rubber had turned gooey...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4