Search:

Type: Posts; User: rgl10; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Re: looking for thoughts on different 4th cylinder cooling options

    I ran mine from the freeze plug on the end of the head to the inlet side of the water pump. Fixed the number 4 spark knock problem for me. As a side note this will flow a lot of water bypassing your...
  2. Thread: AC How To?

    by rgl10
    Replies
    131
    Views
    44,341

    Re: AC How To?

    I have the same thoughts as Miles but I will add that in my experience if you want a truly cold system replace the h-valve and dryer especially if the system has been open very long to atmosphere or...
  3. Replies
    11
    Views
    29,704

    General Re: Shelby lancer, daytona parts. Garage clean out.

    Thanks for the quick shipping and nice parts!
  4. Replies
    47
    Views
    40,319

    Re: MPSciLink possible Group4 Pre-Order Interest?

    Put me down for 2 assembled with 7" screens. Thanks!
  5. Replies
    11
    Views
    29,704

    General Re: Shelby lancer, daytona parts. Garage clean out.

    Pm sent.
  6. Thread: Back in the game

    by rgl10
    Replies
    5
    Views
    8,595

    Re: Back in the game

    Awesome car and I like the Mopar Garage too!
  7. Replies
    25
    Views
    24,101

    General Re: Spirit R/T complete partout

    PM sent
  8. Replies
    13
    Views
    11,823

    Re: Why do I keep finding dead fuel injectors?

    Any chance you have something going on with your fuel? Do you use any additives? I know that some injectors seem more prone to be damaged by high ethanol content if they were not intended for E85...
  9. Thread: Read These Plugs

    by rgl10
    Replies
    13
    Views
    14,592

    Re: Read These Plugs

    They don't look like they have burnt much oil from what I can see. How much oil is the engine using? If its like a quart in 500 to 1000 miles and its getting into the combustion chamber you can...
  10. Replies
    4
    Views
    8,697

    Re: 555 bearing and axle seals

    I really like your videos on youtube! Something I tried on my last transmission and that seems to work well is an axle stabilizer. Its kinda expensive so I only used one on the drivers side of my 5...
  11. Replies
    8
    Views
    7,653

    Re: Turbonator Nitrous Timing retard

    Should be power supplied from cruise switch as one hot wire goes to switch and then three wires to go to smec from the cc switch.
  12. Thread: Murphy

    by rgl10
    Replies
    3
    Views
    4,614

    Positive Re: Murphy

    I agree! I bought several things from him in the last couple of weeks. Everything was exactly as described and shipped very quickly.
  13. Replies
    6
    Views
    6,958

    Electronics Re: Need 91 Shadow engine harness 2.5 turbo

    Still looking
  14. Replies
    2
    Views
    13,738

    Re: Turbo Van overheating/air in system

    Normally drilling is not required. However it will make bleeding the air out easier. 1/16 or smaller is enough. Put the hole toward the top when thermostat is installed of course. Make sure your...
  15. Replies
    3
    Views
    7,363

    Electronics Re: Spirit Turbo Wiring Harness

    Pm sent
  16. Replies
    8
    Views
    8,719

    Electronics Re: ECUs - 3.0, MP LM, 89 T2

    Pm sent
  17. Replies
    4
    Views
    8,247

    Re: Clutch pedal noise and remediation

    I think I will give that a try on mine. Its not overly stiff but any reduction in pedal pressure is good for me old clutch leg.
  18. Replies
    2
    Views
    3,026

    Re: 2010 Caravan electrical issue

    I can email you most any diagram you need. That multi-function switch controls the wiper, turn signals and head lights. Its called the SCM, steering control module. If you have access to a snap on...
  19. Re: Poor heater output at idle, 2005 Grand Cherokee. I'm stumped!

    You said both hoses are 10 degrees apart. Do they run 190 or so when the engine shows 200? If both are that hot then you have an air flow problem. If they both are lower like 120 or 130 at idle then...
  20. Replies
    35
    Views
    18,370

    Re: Chip reader/burner for SBEC chips

    The errors on the second two seem to be from the programmer not recognizing the chips or the chips are not TMS87C257.

    Edit- Sorry Miles I was researching that very thing and you beat me to it lol.
  21. Replies
    7
    Views
    11,260

    Re: Simulator research

    I am just wiring up the sbec like it would be in a car. Small 12 volt motors turn the distributor and vss. I use bulbs in place of injectors and the coil. I have all the important stuff hooked up,...
  22. Replies
    35
    Views
    18,370

    Re: Chip reader/burner for SBEC chips

    I have used the willem burner with some success but i recently switched to the TL866CS and its much faster and so far no problems. I have programmed the electrically erasable chips for the 88 and 89...
  23. Thread: GLH Turbo cars

    by rgl10
    Replies
    11
    Views
    7,431

    Re: GLH Turbo cars

    I definitely want to see that!
  24. Replies
    7
    Views
    11,260

    Re: Simulator research

    Who would be best to use to host images?
  25. Replies
    7
    Views
    11,260

    Simulator research

    Built an sbec simulator and posted the details in the electrical and fuel guru temple but didn't realize at the time that a lot of people can post comments to that thread so I will add this one for...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4