Search:

Type: Posts; User: Kevin_Hemenway; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    971

    Re: Cam cap studs

    Thank you. I will get studs and bolts from McMaster
  2. Replies
    5
    Views
    971

    Cam cap studs

    Has anyone ever put studs in for your cam caps? I have a head that has some stripped cam bolt threads. I want to do studs so it is a non issue going forward. Does anyone have any experience putting...
  3. Replies
    82
    Views
    20,898

    Re: 36-1 Trigger Wheel Crank Pulley Adapters

    I would like one also probably two
  4. Replies
    20
    Views
    9,288

    Re: Misfiring Under Load

    Preignition/Detonation?
  5. Replies
    25
    Views
    9,693

    Engine Re: FWD Thermostat housing

    I was under the impression rockauto was an approved vendor for this forum. I'm sorry I brought them up just trying to help annother enthusiast get a product somil6to what they wanted.
  6. Replies
    25
    Views
    9,693

    Engine Re: FWD Thermostat housing

    The last two I bought from rock auto were cast housings not stamped tin like stock very nice in my opinion and very cheap just not as pretty as the fwd one64894
  7. Re: Putting 3.05 ring and pinion in an A413

    Has anyone made a retainer for the transfer gear nuts? Any photos?
  8. Replies
    5
    Views
    4,529

    Re: Steering Rack interchange

    I did get the cardone one but I converted it to a manual rack before I installed it, I couldn't say how good it would have been. Works well as a manual rack in my racecar tho.
  9. Replies
    5
    Views
    4,529

    Re: Steering Rack interchange

    I got my last one from rockauto.com
  10. Replies
    6
    Views
    2,929

    Re: Plug wire distributor terminal

    I have a set of msd wires I was wanting to use. I like the taylor ones you linked if I had seen them before I got the msd I would have gone that route.
  11. Replies
    6
    Views
    2,929

    Plug wire distributor terminal

    Does anyone know where to get the terminals for plug wires that clip into the distributor cap?
  12. Re: Putting 3.05 ring and pinion in an A413

    I am not sure why the angle would be different I cant find any information about compatible gears vs. The grooves
    64640
  13. Re: Putting 3.05 ring and pinion in an A413

    I finally found a set of gears that will work. I found that the rings and pinions come with different grooves in the gears and only certain ones will fit together correctly. After ordering from 4...
  14. Re: Putting 3.05 ring and pinion in an A413

    I cant find any transmission place that has the 3.05 ring and pinion I need so I will be checking scrap yards does anyone know an easy way to check if a vehicle has the parts without pulling the...
  15. Putting 3.05 ring and pinion in an A413

    I have ordered 2 separate (20/61) 3.05 ring and pinion sets. Neither of them seem to mesh together. Has anyone had any experience with this.64610
  16. Transmission Re: Looking for A413 transmission gear sets

    I do have a question. I read on annother post that some of the 1.22 gears need to be machined to work anyone have any knowledge about this?
  17. Transmission Re: Looking for A413 transmission gear sets

    Doesnt get driven on street. Drag strip only, if I ever make it to one of the MNSDAC meets I will get with you about swapping some gears. I was able to pick up some 1.22 gears today on ebay NOS. They...
  18. Transmission Re: Looking for A413 transmission gear sets

    I believe all of the xfer gears I have are .91. I am always looking for spare non lockup's I busted up 2 of them last season. Is that not the most common size? My transtar book shows a 1.06 option...
  19. Transmission Looking for A413 transmission gear sets

    Looking to get my gear ratio lower on my 89 lebaron with the A413 trans. Wondering if any one has or knows of a set of 53/56 xfer gears. And a 12bolt Ring&pinion 20/61
  20. Re: 2019 Turbo-Mopar Times - DATA COLLECTION THREAD!!!

    1989--Chrysler Lebaron GTC--2.5L T-II FMIC---A413--Hoosier 225/50R-15DR2--Kevin Hemenway JR-- Kevin_Hemenway--http://www.turbo-mopartimes.com/flags/us.jpg
    1.829--8.125@84.16---12.847@103.37...
  21. Replies
    11
    Views
    16,445

    Re: Floor Pan Restoration

    I did all 4 corners on my 89 lebaron this last February. had to cut and bend all sheet metal to fit, by hand. I used thin cardboard for pattern then transferred to metal. I would recommend using a...
  22. Re: Group Buy Pre-Orders for TU Limited Slip Differentials

    got mine yesterday will install next weekend in A413
  23. General Re: Looking for front floor pans for a 1989 Dodge Daytona

    I just did mine in my 89 LeBaron i couldn't find any pans anyplace. I ended up making my own out of sheet metal.
    http://www.turbo-mopar.com/forums/attachment.php?attachmentid=63771&stc=1
  24. Re: 2.5 one piece intake manifold modification

    I feel that reducing turbulence can not be a bad thing.
  25. Re: 2.5 one piece intake manifold modification

    inside i just smoothed out all the bumps and such no runner modifications. I will port match to head when I get it from FWD Motion. I will put temp sensors in both pipes before and after intercooler....
Results 1 to 25 of 49
Page 1 of 2 1 2