Exotic Electron - Prime Ad

Search:

Type: Posts; User: BadAssPerformance; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.80 seconds; generated 4 minute(s) ago.

  1. Re: Officially, the Official Turbo Minivan Build Page

    Welcome back! Thread moved to "Project Log" section :eyebrows:
  2. Re: 2015 SDAC Calendars FOR SALE - Limited Quantity!

    Picked up the calendars tonight! First batch to go out in the mail tomorrow! If you didnt get in, order one tonight!
    52422
  3. Re: High rev shifting difficulty, clutch too heavy?

    Yeah, I had to drill out the hole in the shaft and go a bit larger pin



    As turismolover22 said, the pin in the shifter housing will lock the selector centered. For 520/555 there are two cables...
  4. Re: High rev shifting difficulty, clutch too heavy?

    I would start by making sure everything is "tight" Most of my missed gears over the years were more due to slop in the system than anything.

    You probably already checked this stuff but some things...
  5. Replies
    0
    Views
    103

    Sticky: 2015 SDAC Calendars!

    Group Buy Thread Here:
    http://www.turbo-mopar.com/forums/showthread.php?76854-2015-SDAC-Calendars-FOR-SALE-Limited-Quantity!
  6. 2015 SDAC Calendars FOR SALE - Limited Quantity!

    OK Turbo Mopar and Shelby Dodge fans, HERE IT IS! The official 2015 SDAC Calendars!

    First off, THANK YOU to ALL who submitted pictures this year. There were DEFINITELY some great pics submitted!...
  7. Replies
    10
    Views
    249

    Re: Stuck on side of road

    Interesting that it idles OK but dies on throttle... almost like its not getting enough fuel so it chokes out. Fuel pump on? relay and wiring OK?

    Definitely check the wiring for the hard start. ...
  8. Replies
    29
    Views
    1,002

    Re: My 68 Homemade Turbo Slant6 Dart

    Oh, I know there are quick ones out there, have even seen them, just not many



    12 total timing should be enough at high RPM... down low you'll want more though

    I watched it 3 times and...
  9. Replies
    3,168
    Views
    207,860

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    I really think the 24.5's wont hurt the parts nearly as much as the 26's so really was just trying something different... The twin disk is really grabby so I had to slip the F out of it to not bog or...
  10. Re: Idle above 1500 RPM and won't settle.

    As said, check SDS and wiring and also check the orange fusible links behind the battery. I had similar symptoms and code 15 and didn't figure it out until it didn't start and found a corroded wire...
  11. Re: Print your own Shelby Lancer Wheel Center Caps

    Nice work Andy! :clap:
  12. Replies
    15
    Views
    448

    Re: My last two time slips from 2014

    Nice work OhioRob! Glad you made it out one more time this year, car is moovin!
  13. Replies
    5
    Views
    252

    Re: Injectors Question

    Yeah, it will actually drive OK with the larger injectors, the problem will be at idle when the computer goes into open loop (no O2 feedback) and you will have 20% more gas washing down the...
  14. Replies
    29
    Views
    1,002

    Re: My 68 Homemade Turbo Slant6 Dart

    Nice project car! 4-door sleeper too!

    One of the Chicagoland Mopar Club guys, Dennis (Slantzilla maybe?) just runs nitrous on his and says everyone using a turbo has issues. I'd love for yours...
  15. Replies
    36
    Views
    1,642

    Re: SDAC and Carlisle 2015

    Thanks Barry. I would guess this is still true today
  16. Replies
    36
    Views
    1,642

    Re: SDAC and Carlisle 2015

    Vegas would be fun but difficult at the same time. We do not have a local Chapter or many members near there and June is pretty warm there.



    Dave and I talked about doing this and plan to,...
  17. Replies
    3,168
    Views
    207,860

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Catching up... run recap from Monster Mopar Weekend in Norwalk in September.

    It was a GREAT event, and a lot of fun racing with Reeves, OhioRob, 92TurboSpiritES and more and hanging with all...
  18. Replies
    3,168
    Views
    207,860

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Actually they were a separate runs. re-quoted the run breakdown from the Nats below. Pretty sure the axle only went cuz it went thru all the 26" tire hits and built up fatigue cycles

    Thanks,...
  19. Re: Shelby Lancer #478! (65,000 and rip)

    Unfortunately for this one I only had the add reference and not a name
  20. Replies
    3,168
    Views
    207,860

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    New trans before and after hours of cleaning and rebuild

    522475224852249
  21. Replies
    3,168
    Views
    207,860

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Been busy and away, finally got a break... trying to repost pics of Mopar Nats carnage

    Axle:
    52231522325223352234

    Trans:
    5222952230522355223652237522385223952240522415224252243
  22. Re: lengel's TIII Omni GLH progress (used to be spirit r/t)

    ...and I was thinking is like the 555/568 where the gear and bearing housing are one, LOL! It might not bee too hard then!



    Only on 26" tires and enough force to break bearing backup plates in...
  23. Replies
    6
    Views
    288

    Re: Just a Newby saying hello!

    Welcome!
  24. Re: lengel's TIII Omni GLH progress (used to be spirit r/t)

    OK, lets see if there is enough interest. So we don't clutter lengel's thread... all DSS GB inquires, please go here:...
  25. DriveShaft Shop Axles - Group Buy

    A few have contacted me asking about DSS axles so I thought I would throw it out to see how much interest there is.

    What are Drive Shaft Shop axles? One of the few badass axles made that fit our...
Results 1 to 25 of 117
Page 1 of 5 1 2 3 4