Search:

Type: Posts; User: chromguy; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    324

    Re: Omni with 2.2 turbo engine codes woes

    https://drive.google.com/open?id=1eRUt8JZea226V8fJNM6EvgL8gWAZ5uRp
  2. Replies
    22
    Views
    324

    Re: Omni with 2.2 turbo engine codes woes

    I have connectors index on the SBEC 60 way. IE Map=1 Cool=2 Battery=3 Sensor ground=4 Ign=9 ground =11-12 25 =Tx and 45=Rx for example
    Is this what you are looking for?
    I also have this in a...
  3. Re: SBEC Electronic schematic/flowchart/logic diagrams

    reverse engineering is difficult and slow for everybody. When you find info please share.
  4. Re: SBEC Electronic schematic/flowchart/logic diagrams

    I have pseudo schematics for the 87 LM which will give you an idea of what goes on in the SBEC.
    https://drive.google.com/open?id=0B3qZZUQ9qnBldFlnampwazNzYXM

    I have Reversed Engineered the...
  5. Replies
    18
    Views
    604

    Re: Sci/FTDI cable issues

    Good catch Dan
  6. Replies
    18
    Views
    604

    Re: Sci/FTDI cable issues

    If you have the ability to solder, I would recommend to reflow the solder on the pins, Including the Rx,Tx and ground pins of the SCI connector as several are not soldered on both side. This may or...
  7. Replies
    18
    Views
    604

    Re: Sci/FTDI cable issues

    Send us a picture of both sides of the board, it could be an assembly issue.
  8. Replies
    8
    Views
    330

    Re: SBEC injector drivers

    Dan,
    Last night I checked the MOSFET requirement for speeduino that only works as is for high impedance injectors, they use a STP25N504Z that is rated for 80A ....They don't recommend you use low...
  9. Replies
    22
    Views
    1,436

    Re: Woosh from brake booster

    I decided to test on my Sundance DD as the cooling system crackles after driving and I can hear things boil slightly.
    Now the problem...
    This product caused my rad fan to stop working even on an 85...
  10. Replies
    8
    Views
    330

    Re: SBEC injector drivers

    Dan,
    i test a few SBEC and SBEC2 drivers in circuit with my transistor tester but no luck. I guess I need to unsolder them to fully characterize.
  11. Replies
    8
    Views
    330

    Re: SBEC injector drivers

    Low vs high impedance???? I have no idea what is type A or B.. google search was of no help either
  12. Replies
    2
    Views
    161

    Re: MPTUNE - Rich idle/part throttle HELP

    What I have done in the past is lower the injector size reported in MPTune by small amount (10% to let say 65lb).
  13. Replies
    27
    Views
    3,836

    Re: Cam Numbers/Roller Rockers

    Woops!
  14. Thread: Lizard Skin

    by chromguy
    Replies
    12
    Views
    2,476

    Re: Lizard Skin

    .
    I live in the salt belt. My car in the picture is 32 years old and my DD.
    http://www.turbo-mopar.com/forums/showthread.php?84332-Can-t-install-LSD-in-A555&p=1148367&viewfull=1#post1148367...
  15. Replies
    8
    Views
    330

    Re: SBEC injector drivers

    Hi Dan,
    I checked a SBEC2 that I have hacked and three that I could read have a PH4947 but I could not find any info on them. Perhaps a special Cryco part number and one also had a Chrysler part...
  16. Replies
    8
    Views
    330

    Re: SBEC injector drivers

    Hi Dan,
    I can have a look tonight to see if I can cross-reference.
    My guess is C as the injectors are approx 2 ohm and thus 14/2 = 7 amp albeit for a short period of time
  17. Re: Colour code for SBEC2 driver alignment assemblies

    Interesting that I just found a SBEC2 with the same combo as the Turbo but without several of the MOSFET drivers installed.
    Rats, now things are more complex, what a shocker!!!
  18. Replies
    10
    Views
    432

    Re: replacing vacuum lines

    ais site:www.turbo-mopar.com in google the colon tells google to only search "ais" on the web site after the colon

    here is the link using DuckDuckGo...
  19. Re: Colour code for SBEC2 driver alignment assemblies

    Thanks Brian,
    I will write up with picture what I need over the next day or so
  20. Colour code for SBEC2 driver alignment assemblies

    Anyone with information on the colour code of the plastic clip that is used to push the MOSFET drivers in contact with the heatsink. I have seen Red, Green, Yellow, Black, Gray, Blue, Orange,...
  21. Replies
    0
    Views
    87

    SBEC2 PCB part numbers

    We are looking for part numbers of PCB boards of SBEC2 so far I have found
    463-2377 I have only found these with T1 and TIII configurations.

    451-7652 I have multiple V6 versions such as 3.0...
  22. Replies
    5
    Views
    276

    Re: front end poping sound 83 rampage

    http://minimopar.net/centerengine.html
    How To Center Your Engine Description This page describes the procedure for engine centering. It is important that you do this if you ever remove your...
  23. Replies
    10
    Views
    432

    Re: replacing vacuum lines

    Yup, happened to us all!
    On the vacuum lines, I use teflon with Pieco fittings as it was in the dumpster at work. I hate when that happens!
  24. Replies
    10
    Views
    432

    Re: replacing vacuum lines

    LOL, yes I do not see your picture except in your other post. We have found that using the advanced function is much more reliable
  25. Replies
    5
    Views
    276

    Re: front end poping sound 83 rampage

    I have also found worn rear stub strut bushing themselves can make the sound, in fact, mine are starting to make that sound a month ago or so. I replaced them 130,000km ago, time for a refresh
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4