Search:

Type: Posts; User: tryingbe; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    38

    Re: Clutch pedal goes to floor

    Is the clip and bushing still on the cable end at the transmission?
  2. General Re: Rebuildable K-car Koni, 2.5in swingvalve, 2piece intake manifold, +20 injectors,

    Yes. Fits any K based car, Daytona, Shadow, Spirit, Laser, Aries, Sundance, Lancer, Dynasty, 600, and etc.



    2 bar map sensor with a MP LM was installed. There was also a 87 LM in the car. Left...
  3. General Rebuildable K-car Koni, 2.5in swingvalve, 2piece intake manifold, +20 injectors, etc

    Date: 24th August 2019
    Username: tryingbe
    Full Name: Harry Lui
    City, State, Zip: Mesa, AZ 85204
    Contact: tryingbe at yahoo dot com


    All parts came off a 88XXX miles 1987 Daytona Shelby Z from...
  4. Replies
    3
    Views
    38

    Re: Way to rich cold start

    It's 10.0 because that's all your wideband can measure.
    What size injectors are you using?

    This may help.
    https://www.turbododge.com/forums/f4/f21/1243450-rich-idle-ostrich-2-0-a.html
  5. Re: 1989 Dodge Shelby Daytona with only 34k on it

    What's the vin number?
  6. Replies
    11
    Views
    241

    Re: HP Gain From K&N Filters?

    I'll stick with paper filter.

    Paper filter have larger filter area and do a better job to keeps dust/dirty.
  7. Replies
    39
    Views
    6,131

    Re: AZ Turbo Mopar Monthly Meet.

    https://www.tempechryslerjeepdodge.net/
    https://www.billluke.com/

    Not sure which is closer to you.
  8. Replies
    39
    Views
    6,131

    Re: AZ Turbo Mopar Monthly Meet.

    A.J.'s shop have a/c in the customer area.

    So, no meet this week?
  9. Re: TII intake thread pitch for air charge temp sensor

    The element can't pass thru 33004280 sensor
  10. Re: TII intake thread pitch for air charge temp sensor

    Thanks Todd,

    I ran 25psi on 33004280 sensor for a few years with no issue.
  11. Re: TII intake thread pitch for air charge temp sensor

    I relocated my air charge temperature sensor to the charge pipe after the intercooler, it really helped with heatsoak restart and other heatsoak related issue.
    I used 33004280 caged sensor....
  12. Replies
    39
    Views
    6,131

    Re: AZ Turbo Mopar Monthly Meet.

    Meet is tomorrow!
  13. Replies
    1
    Views
    119

    Suspension Re: L body camber plates for FWDP coilovers

    http://www.turbo-mopar.com/forums/showthread.php?79555-L-body-Koni-coilover-with-camber-plates-and-other-improvements&highlight=bearing+plate
  14. Replies
    27
    Views
    3,833

    Re: Cam Numbers/Roller Rockers

    http://thelostartof.net/tryingbe/dodge/slidercam_on_rollerarms.jpg

    Someone just tried out what slider cam can do with roller rockers.
  15. Replies
    9
    Views
    840

    Re: Can't install LSD in A555.

    Get him to take pictures.
  16. Thread: MBC vs EBC

    by tryingbe
    Replies
    7
    Views
    1,842

    Re: MBC vs EBC

    I installed the HDi dual mode boost controller since 2015, yes initial cost of $130 is high, but adjusting boost is so much easier and my boost level is pretty rock solid after shorting my vacuum...
  17. Replies
    41
    Views
    14,015

    Re: CSX VNT rear brakes

    The calipers are discontinued by re-builders, and will be expensive if you do find one. One of my friends paid $300 for a rebuilt one for his TC, if I remember correctly
  18. Replies
    48
    Views
    9,501

    Sticky: Re: MPTune non Turbonator cals

    If I remember correctly, Turbonators cals are too rich at part throttle and too lean at WOT right out the box. Turbonators cals are meant to be modify before use and you shouldn't use them if you...
  19. Replies
    3
    Views
    3,254

    Re: Wiring issues.

    N13 20 DB/OR* A/C cutout relay output
    K7 18 OR/DB* Throttle position sensor (TPS) signal

    http://minimopar.net/ecu/lm-1986-t1.html


    Read this for TI to TII conversion.
    ...
  20. Replies
    21
    Views
    3,193

    Re: Omni GLHS alternator harness replacement

    Engine Coolant Temperature sensor is two wires. One is ground signal from ECU, one is signal to ECU, what are you trying to do?

    http://www.minimopar.net/ecu/coolant_temp_se.html...
  21. Replies
    21
    Views
    3,193

    Re: Omni GLHS alternator harness replacement

    I used 0/1 gauge welding cables to make new alternator and starter harness following original harness.
    When I moved onto Microsquirt, I bought all new wiring and connectors for all the sensors.
  22. Replies
    1
    Views
    229

    Re: Microsquirt v3 trigger wheel?

    MS manual
    http://www.msextra.com/doc/pdf/html/Microsquirt_Hardware-3.4.pdf/Microsquirt_Hardware-3.4-52.html


    Wire diagram is also in there....
  23. Replies
    4
    Views
    298

    Re: Deceleration RICH condition?

    Why not just adjust your cal and see what happens?
  24. Replies
    4
    Views
    298

    Re: Deceleration RICH condition?

    FuelBaselineFromMap is used when no throttle is applied.
  25. Thread: Red Baron

    by tryingbe
    Replies
    68
    Views
    21,551

    Re: Red Baron

    I thought my GLH's engine bay is tight. Good job.
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4