I have an black 89 Shelby Daytona t-top car that I am thinking about selling. Second owner purchased in 1992. Car body, paint and interior is very clean with virtually no rust. It has been heavily...
Type: Posts; User: mckeonm; Keyword(s):
I have an black 89 Shelby Daytona t-top car that I am thinking about selling. Second owner purchased in 1992. Car body, paint and interior is very clean with virtually no rust. It has been heavily...
Sounds great.... I'm not pressed for time, just would like to do something before the end of summer.
Hello,
I have an 89 Shelby Daytona that I took off the road about 18 months (drained all the fuel before doing so) ago and would like to get it back on the road. Long story short is, I use to...
Ok, checked the voltage on the map and it is a two bar map. I also had a friend(non turbo dodge guy) with a OBD1 scan tool come over. I was getting a MAP fault code "no change in signal" and a...
I am aware of not just throwing in a 3 bar map and expecting to run better. The computer I have is from forward motion and did require a 3 bar map.
Is there more detailed instructions on testing...
I installed the newly acquired +40 injectors, adjusted the fuel pressure down to 45 psi with vacuum line removed and installed what I think is a 3 bar map, is there any identifying mark to know for...
Unfortunately I could not find my 40%s, and will need to source some. I did get the part number P4532176 off the current injectors, does anyone know what injectors they are?
The Super 70 is a remapped computer from Forward Motion a small step up from the 60 I'm not sure if they call that anymore. I do have a set of 40%s I can throw on the car and a 3 bar map. ...
I have a super 70 computer, run 20% injectors all grounds are in tacked. I have the submersible fuel line hose on the pump as well. When it was running for the 20 minutes or so it was not pulling...
I got the Shelby running last night and drove it about 20 miles today. It would not start up right away, took a 10 seconds or so to start. Once it was running it had high idle (2500 rpm) for about...
Hello,
I got my 89 Shelby Daytona running last night. While on a test drive I noticed that under full boost and WOT that my oil pressure gauge quickly (1-2 seconds) drops until the needle can't...
Wanted to replace it today or tomorrow. Any suitable auto part store pump?
Update,
Replaced filter and sock on fuel pump. Reinstalled and started right up, then died. 0 fuel pressure & pump does not run now when jumped. I guess I now have to replace pump. Any...
Great idea supercrackerbox, worked like a champ, I was able to remove all but 2 gallons of gas.
I got the pump out and the first thing I notice was the pick up filter sock was not attached. I...
Ok, I've done the above and still not getting above 30 psi. I am going to pull the pump out and check the hose for deterioration.
Issue now is I have a full tank of gas. Anyone have...
hard too do that with stainless steel braided lines:confused2:
I will give the suggestions a shot.
I'm working on an 89 Shelby Daytona that has a Holley 255 pump. When I turn the ignition key to the on position I do not hear the pump turn on. My fuel pressure is at 26 Psi in the on position and...
Many SDAC guys out tonight?
Hello,
I'm looking for some local help (Ann Arbor, MI) with trouble shooting some starting and tuning issues with my 89 Shelby Daytona. I have not done much work on my Shelby in the last 8-10...
I live off Happy Valley Road less than 7 minutes from this shopping center. I will be working and should be home by 3:45. I will be then going down to Norterra for the show.
No it does not cost anything, It's free. Line up in the back of the shopping center. We line up in a horseshoe shaped line in the parking lot between the two north exits (cars start lining up around...
Cool... lets hope the weather is good. I was there in December and it was cold.
Matt
Hello,
Just trying to gauge some interest on getting some TM's together on Friday night the 10th of February at the Norterra Shopping center at Happy Valley Rd & I-17. This is a car show (open to...
How much to you want for one?
Hello,
I recently troubleshooted a problem I had with my passenger window not going down on my 89” Daytona. It ended up being the switch itself. I removed the switch assembly and took of the black...