Yeah, I was in disbelief when I saw the box!:) I threw it in the closet because it had a pretty cool design. I guess it is probably a generic Garrett box, and they just packaged the TiAl in it. There...
Type: Posts; User: Bossman429; Keyword(s):
Yeah, I was in disbelief when I saw the box!:) I threw it in the closet because it had a pretty cool design. I guess it is probably a generic Garrett box, and they just packaged the TiAl in it. There...
I had no idea, from all of the companies that carry the valve they made no indication that the valve was made by Garrett .
It came in a box that said "Garrett Turbochargers"
It is also pictured and...
As far as quality aftermarket BOVs go, the RFL is probably one of the cheapest around. I have heard a lot of people doing well with them.
I have a Garrett TiAl on my GTS, and it ran me right...
Ahhh, that wasn't too long of a post.:)
Well, according to the service manual it's an "intergral tubular stabilizer bar"
That is of minimal importance though.
I'm going to get a rear 1" bar from...
Looks like trying to drill it with the trans installed runs way too much of a risk of chewing up the ring gear.
My question is answered, thanks!:thumb:
Simon, have you found out anything on the crab wheels?
I think as long as they have 225/50 tires on them they should be 6.5 wide, 6 wide *should* have 205/60s.
I really want to ditch my lace wheels...
Are you doing this with the transmission in the car, or out?
Either way, I wouldn't mind seeing some pics of the job, if you have time.
Simon,
Are those crab wheels 15X6 or 15X6.5?
I've read that the Daytona crabs were 6.5 wide since they had 225/50's on them.
Polished lip?
Good shape? I mean not bent or anything, I expect a...
That bar is going to be a lot wider, but could probably be cut to fit. Many of them are curved as well, while the Cavalier bar is straight.
I guess that's why we're in the fabrication section.:)
When you box an axle, do you box the entire length of it like the panhard bar? Should I just box it in sections, or weld an entire length of steel to it?
Well, as luck would have it, we had an 83 Dodge 600/Aries in the shop today, so I could take a look at what my rear end SHOULD look like.
From the looks of things I could either:
A. get a piece of...
The factory lace wheels on my Beretta are 15 X7, and I think all of the body colored Beretta GT wheels are 7 inches wide. With the exception of the gray lace wheels which are 6 inches wide.
I have a...
That's much easier said than done around here.:(
It's a Mopar Cal for all I know. It's not an aftermarket.
OK, so my GTS handles terribly, I mean, it holds the road just fine, but the body roll is unbearable.
So I decided to put it up on the rack, and see what I have to deal with before I decide on a...
I entered the VIN info (3rd, 5th, 8th, 10th digit) into the scanner. It listed an SMEC code to choose, but only listed one, I think.
I didn't know what the code should have been, where can I check?...
It's a Snap On "Red Brick" scanner.
I don't recall what the SMEC code was, all I remember is that it might have been 54XX. It's a 1989 ECM.
When I unplugged the CTS on the t-stat to adjust the...
So I finally got around to hooking up a scanner, and monitoring some of the numbers my SMEC is seeing while running and such. A few caught me off guard:
Coolant temp: showed 14,000 ( it was a 5...
I need to do this some day too. I was worried about cutting it short, then racking my elbow on the console lid in fast shifts, I don't think it will be a problem though.
When I'm racing I grab the...
Hey, that's a pretty good idea!
Those bars are available at GM for about $30 new unless you can find one in a yard. They came factory in the 90-94 Cavalier Z24s, and V6 convertibles.
I have one on...
*Gasp!*
Topeka, Eh?????!!!!!!!!!!!!!
That's so close I'd ba a fool not to go!
I have Sundays off at work too, so SDAC would be a go for sure!
Hope to see many of you who have helped me...
Thanks for the PN!
I ordered 4 of them so I have some extras, should be here Wednesday. Can't wait!
I'll keep an eye on that!
Can you tell me what the overall dimensions are including end tanks?
I want to see how hard it might be to fit, etc...
No pics?????!!!!
BOOOOOOOOO:)
I finally spotted another H body in town last Sunday, it was a turd though, not even a turbo car, bah!
PM sent:)