Search:

@contraption22 That would be really really helpful! Thanks!

Hi all,

I need a headliner board for my 86 Plymouth Horizon, mine was missing when I bought the car. If I could find one in great condition in the factory grey, that would be great, but Id settle...

Hey guys, Im looking for the elusive intact omni rear package tray, preferably in gray, but at this point, I am not that picky!

Please let me know if you have one or can post a link to one.

...

You know, i have an 86 horizon that all that stuff would look really nice in :-)

Thanks! That gives me a starting point and some ideas :-)

Hi guys!

I wasn't sure where to put this, so if its in the wrong section, just let me know!

Ive been kicking around putting the air conditioning back into my horizon and if that goes well maybe...

I would be interested in the intake, exhaust and the turbo... dont really need the head itself! But I would need them shipped to Oklahoma 74403!

Thanks! That will be a big help! So whats the best way to remove the seals themselves, do they pop out easily? Is there a recommended procedure? Or will just a flat head screwdriver get the job...

Thanks very much for the info! That will be a big help!

Tifany

Hey all!

I have an 86 Horizon that is leaking fluid from the seals around the cv axles. Im having pproblems finding new seals since no one seems to know what they are actually called. Also, what...

Allright, so I just have to swap the rods and pistons, keep the turbo rings and put them on the non turbo pistons and make sure that they go back in the bore that they came out of. That seems very...

Yeah that's what I was afraid of. I'm still wondering if it would be worth the effort to swap the pistons for the higher compression ones. The rods are the same for both in 86 aren't they?

Thanks...

Hi Guys!

I have an 86 horizon carbed 2.2 with a blown motor, I also have access to a an 86 turbo motor (but with no intake or exhaust manifolds). My question is: how well would the turbo motor...

Date: 14th June 2013
Username: LaserGurl
Full Name: Tifany Oslin
City, State, Zip: Muskogee, Ok 74401
Contact: email: tifanyanne@yahoo.com or PM me and I will be happy to give you my phone...

Yikes! good to know!

Thanks!

Tifany

OK thanks! Was kinda stressing! has been a long time since ive had one of these apart and I couldnt remember if this was how it was supposed to be! It seems like bigger passages in the gasket would...

Hi guys!

Im working on replacing the head gasket in my 86 horizon N/A car because its been overheating and over-pressurizing the cooling system. Anyways, when I pulled the old gasket out, it...

Hi guys! I was wondering what I would have to do to put the rallye gauge cluster out of my 87 charger (NA) into my 86 horizon (also still NA). All the Horizon has is the fuel gauge, speedo, and...

what Ive been trying is about five mins of cranking time, followed by a few minutes to cool down the starter, but several repeats to that sequence. Kept that up for over 20 minutes or so. Its getting...

Its a mechanical pump... and brand new. When I pulled the lines off when i was replacing it there was fuel in the lines... may have just been trapped in there though. Ill pull the lines back off...

Hey guys!

So, Im trying to get my 86 carbed horizon back on the road, its been sitting for a few months. I put a new weber carb on it and then havent had time to mess with it for a while. The...

Ok, Ill try that in the morning and see what happens!


Tif

Hey all!

I have an 86 horizon that I got a few months ago for a work car. It runs fine, but when I shut the car off I hear boiling water sounds comming from the radiator. I already pulled the...

Hi!

I think I've got one lined out already but if that falls through Ill give ya a pm!

Thanks!

Tif

Hey guys!

Im looking for the slideing cup holder that goes inside the center console of an omni/charger. I really just need the cup holder part, but if I have to buy the whole console piece...