Search:

Type: Posts; User: Dr. Johny Dodge; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    181

    Re: 84 daytona heater Controls?

    there were two different control panels used for a daytona .. might be really early vs everything else .. so dodge truck .. maybe maybe not

    the two panels do look different

    I know the heater...
  2. Replies
    16
    Views
    464

    Re: L body door pins and bushings

    L body used an early vs late door hinge pin

    with an 87 you'll need ""late"

    don't try bending the hinge to correct drop when opening the door

    IF the pin is worn replace the pin.. simple
    ...
  3. General Re: G Body: Laser/Daytona Louvers and Ground Effects for Sale

    when my parrents goyt the kitchen redone the cabnet co sent the new cupboard doors sandwiched between thin veneer grade (thickness plywood sheet )
    about 3/16's thick
    made great box bottoms for...
  4. Re: A good item to store beside your spare HEP...

    best hep advice .. look for the aftermarket one with the soft rubber insolation rather than the hard "phone cable" like leads the factory heps had

    it's the hard insolation that breaks the little...
  5. Re: A good item to store beside your spare HEP...

    had a buddy lose that sme water hose on the off ramp .. hwy 401 to morningside
    hose burst as he went into the curve away from the highway on the off ramp
    car turned 360* with two passengers & a car...
  6. Replies
    64
    Views
    2,021

    Re: AC How To?

    especially our cars used the hoses with the little holes...the big fat rubber hoses are the ones I'm referring to ..not the smaller "braided" looking ones
    it'S THE main reason most ac systems in our...
  7. Replies
    64
    Views
    2,021

    Re: AC How To?

    AC hose has a pattern of micro holes in it
    this often causes leaks when old

    but the micro holes are there for a reason as I believe it's like having a release valve in the system if the pressure...
  8. Replies
    1
    Views
    250

    Re: Sticky tape for cowl trim?

    I'd suggest what we call dum dum here
    it's 10 -ish long x 3/8 - ish diameter strips of black slightly gooey pliable sealer you can use to hold something down or seal a leak

    it's going to be...
  9. Replies
    3
    Views
    436

    Re: quarter glass leak

    the window and the trim frame are one assembled piece that bolts in from inside the car

    it's pretty basic to remove and reseal
  10. Replies
    13
    Views
    670

    Re: GLHS factory shift light

    I'm pretty sure the electronics for the F P light are all inside the spark control computer .. as I converted my 85 turismo ..2.2 carb 5spd to log turbo and I lost the fuel pacer function as soon as...
  11. Replies
    13
    Views
    670

    Re: GLHS factory shift light

    that was called the "fuel pacer light" or something simular
    it goes way back to the early seventies maybe late sixties when mopars used to have the fender top signal indicator lights
    the driver's...
  12. Replies
    13
    Views
    670

    Re: GLHS factory shift light

    shift light ??

    I know the power loss lamp lights up when you get to the limiter .. BUT , I wouldn't call that a shift light ..though I do have a spot where it is a shift lamp ..at the top of...
  13. Re: Car stalls when LM touches chassis

    'scuse da double post
  14. Re: Car stalls when LM touches chassis

    new jersey ??
    any holes in the wheel well in front of the LM ?
    next issue will be keepin it dry if so
  15. Re: Car stalls when LM touches chassis

    note the holes in the LM mounting tabs are much larger than the studs ..
    -this accounts for the plastic insulator sleeve between the stud & case material ..caped with the plastic nut
    7/16 ..I...
  16. Re: Car stalls when LM touches chassis

    for the time being it should run just fine laying on the carpet .. I suspect you need the plastic hardware for mounting it.. so you can at least run it until the parts show up

    as long as no one...
  17. Re: Car stalls when LM touches chassis

    inside the LM there should be a piece of plastic sheet .. you can make something from the top of a christmas card box or something similar

    this shields the circuit board from the case

    the LM...
  18. Replies
    134
    Views
    15,514

    Re: Help me pick some wheels!

    https://www.driftworks.com/rota-rkr-in-steel-grey-15x8-4x114mm-et0.html

    I'm not sure now I ever found an actual stated weight ..

    if you want a good tire calculator
    type the tire size and...
  19. Replies
    134
    Views
    15,514

    Re: Help me pick some wheels!

    I believe you can get those in polished , silver , grey , black and gold somehow or another
    paint or anod ..Idono
  20. Replies
    134
    Views
    15,514

    Re: Help me pick some wheels!

    from the second link..

    I'd presume shipping weight and dimensions (?)

    width="446" style="margin: 0px 0px 1.618em; padding: 0px; border-width: 1px 0px 0px; border-top-style: dotted;...
  21. Replies
    134
    Views
    15,514

    Re: Help me pick some wheels!

    not sure IF I posted already
    rota wheels !!
    ...
  22. Replies
    127
    Views
    15,964

    Re: Head Porting

    I'd be interested in hearing the different experiences peeps have had with different cams

    ..THAT WOULD help with making choices

    I've run the MP 314 cams in ALL my 2.2's over the years
    there's...
  23. Replies
    166
    Views
    31,858

    Re: A555 bronze shift fork pads

    noted thanks !!

    friendly nudge on the end plates too
  24. Replies
    166
    Views
    31,858

    Re: A555 bronze shift fork pads

    any chance for the 520/568 trans ?

    - still interested in one of your billet end plates also ..
  25. Replies
    27
    Views
    1,146

    Re: 86 Logic Module Interchange

    that might make sense with the early fall of 86 build date on my 87 shelby charger's door sticker
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4