Finally got around to drawing this up. Here is my design, up to date for crankcase evacuation.
https://uploads.tapatalk-cdn.com/20200323/a017107d614e546911c6d5abb2249f7d.jpg
...
Type: Posts; User: DoubleD; Keyword(s):
Finally got around to drawing this up. Here is my design, up to date for crankcase evacuation.
https://uploads.tapatalk-cdn.com/20200323/a017107d614e546911c6d5abb2249f7d.jpg
...
I am running into similar issues with my car, but I think that is due to my modified fuel canister, In my experience, none of these cars have a well designed sump that will hold fuel when the tanks...
I have done this in my 92 Daytona, but there are some drawbacks, what car are you trying to install this in?
Some of the boards are available on OSHPark, but it is up to the individual to order the correct components and solder them down. There are no lists that say what parts to order.
I second this! Just make sure you have the right part number depending on if the car has AC or not
Here you go.
https://uploads.tapatalk-cdn.com/20191226/6bc82b098857722f7a40e345040ec602.jpg
Sent from my iPhone using Tapatalk
This is what I built for the 3.5” screen https://uploads.tapatalk-cdn.com/20191226/a749cea530c2538fca2368750c573d30.jpg
Sent from my iPhone using Tapatalk
Digging up an old thread!
I am in the process of trying to program the newer 27SF512 (newer replacement for the 27C256) for use in an SBECII. I have one of the newer latch adapters that is smaller,...
The rings were CNC machined and identical, so I have to take a closer look tonight.
What I am more interested here is if the strut tower "ring plate" should be concentric with the hole in the strut tower? When Rich sent out the template for drilling out the shock tower was that...
Finally got around to working on a guide tool. I went to take some measurements of the strut tower and noticed that my strut tower is not concentric to the cutout in the strut tower. The stock strut...
I am looking to build a hole saw fixture for cutting the holes for enlarging the strut towers. I have already built a strut tower brace so I know where the holes need to be. What size hole saw are...
Took the car to SDAC and the displays were looking good. Had some issues with the EGT working on the way down, but the plug was not fully seated. Oil temp gauge is not functional at all right now,...
Over the SDAC weekend I had a Vibrant Ultra Quiet resonator and Magnaflow high flow catalytic converter installed to replace my 3" Magnaflow resonator. The drone is a lot less at highway cruising...
Built a new to me A523 this spring, swapped over my OBX diff, shift fork pads, and had the intermediate shaft bearing race welded. I replaced both main bearings and re-shimmed the main shaft....
So here is what I did to eliminate the vibration:
I removed the shims under the passenger side motor mount which lowered the passenger side of the engine and made it almost level.
I removed the 2...
Talked on the phone with Johnny today and came home and laid a level across the core support and across the engine. Looks like the passenger side is high, so I’ll be removing the shims....
The passenger one that I received from Johnny is a filled one, it is not the solid one. Can I still remove the spacers?
So I can remove the shims then?
I will pull the shims out of the passenger mount, then loosen the front mount and bobble strut, then torque the front mount and reset the bobble strut with no...
I had the complete motor and trans out. I did not just swap out the passenger mount. Everything was removed and reset. My passenger side had 2 spacers before and I used those same spacers with the...
I purchased mine in April, I am pretty sure I got the longer ones, there was no spacer included. I also got the new rear coil spring mounting brackets that require 2 5/16 holes.
I know that, I am more curious how much pre-load people are running and basically what their ride height is based on the difference between the two lock rings. I know that pre-load is set once and...
What are you guys with the adapted BC's running for suspension set-up.
There was nothing in the box for instructions, so I set up the front coils with 4mm of preload as I read online. I currently...
I just got my 1992 IROC R/T back together with a lot of new parts. I think their may be multiple issue here but I was looking for someone with experience on this. I just rebuilt a new to me A523 with...
I'm coming to my first SDAC, will be bringing my 92 IROC R/T. Looking forward to a fun week!