Search:

Type: Posts; User: Lugert; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. For Sale 1977 Dodge 1-Ton Dually 2wd on Ebay (Its MINE)

    http://www.ebay.com/itm/151557893019
  2. Re: The time has come to breathe life into the "Sha-Dough"!

    Starting Over. Thinking of just building it stock, cast pistons and all!
  3. Re: The time has come to breathe life into the "Sha-Dough"!

    Damn computers. Long reply with failure to load!!!

    Anyway, I did buy a new Torque wrench to eliminate that as a possible problem.

    This same builder built 4 motors for us...All Bad.
    One stock...
  4. Re: The time has come to breathe life into the "Sha-Dough"!

    Originally it was a Copper Gasket Setup with Receiving Grooves in the head. That is how it was built. But never held a gasket (even at Idle).
    Went with a thicker Copper gasket, Bad.
    Went with a...
  5. Re: The time has come to breathe life into the "Sha-Dough"!

    Here are some pics.
    The groove is a groove, not a step.
    You can see how thick the ring is and how much stick up when installed.


    4477144772447734477444775
  6. Re: The time has come to breathe life into the "Sha-Dough"!

    Actually that was tried originally.
    There were receiving groves in the head.
    Tries many different gaskets, many different combinations
    The engine builder is to blame.

    I even went so far to...
  7. Re: The time has come to breathe life into the "Sha-Dough"!

    The o-Ring was properly done.
    It sits in a groove.
    It is suppose to stay there.
    Just looks like excessive heat that caused it.
    Not sure.
  8. Re: The time has come to breathe life into the "Sha-Dough"!

    Me too!, but you of all people would appreciate this car running again! :)

    Motor is OUT!
    Some wierd stuff here with the O-rings going inside the chamber.
    And remember, this motor never seen...
  9. Re: The time has come to breathe life into the "Sha-Dough"!

    Well here is the Donor Motor. Hope all is good with the block.
    I want to stay 2.2 because I like A LOT of boost!

    I guess we will see what the machine shop has to say about my old parts. Not...
  10. Re: The time has come to breathe life into the "Sha-Dough"!

    Robert, nice car!
  11. Re: The time has come to breathe life into the "Sha-Dough"!

    Thanks Bob!
  12. Re: The time has come to breathe life into the "Sha-Dough"!

    Picked up the donor block today.

    44578
  13. Re: The time has come to breathe life into the "Sha-Dough"!

    Oh, Wise Guy!

    Yeah, I really think I might be going back to a completely stock bottom end and stock head.
    I just need to know how far I can go. I was convinced after my last dyno run with my old...
  14. The time has come to breathe life into the "Sha-Dough"!

    Yup, located a block (with a little help from Todd N.) to start a new motor build.
    This will see the track again this year. (I hope)
    44555
    44556
  15. Replies
    50
    Views
    3,076

    Re: Can I run on 16 volts?

    Sorry this is old news, maybe you gave up.
    But just so you know. I have 16 volt regulators for the Denso Alternators for our cars. :)
  16. Replies
    1,266
    Views
    183,218

    Re: Reeves' OMNI GLH-R Update!

    How does this JackWagon get a thread about his car that is over 54 pages long?! :)
  17. Replies
    618
    Views
    126,771

    Re: The Contraption 2013-14

    Good luck on the build!

    Hmmm, Wouldn't it be wonderful if I got off my --- and got my car running again!
  18. For Sale 1987 Dodge Shadow Race Car Make a Serious Offer!

    1987 Dodge Shadow Race Ready Rolling Chassis (With bad motor)

    -10 point Chrome Moly Cage tied into front frame
    -Race Seat with Harness, passenger seat
    -Automatic Console
    -Line Locks, front and...
  19. Replies
    937
    Views
    98,005

    Re: MNSDAC "Minnesota" meeting

    I have one.
    Has not been used in years.
    You are more than welcome to give it a try! And if you like it you can buy it!

    -Bryan
  20. Re: What is stock fuel pressure for a 1992 2.5 Carb car?

    Ended up with a 60 PSI pump, external.
    Worked GREAT!

    40754
  21. Replies
    8
    Views
    2,522

    My 1992 Chrysler LeBaron DEMO DERBY CAR!!

    If you ain't First, You're Last!

    40739
    40740
    40741
    40742
    40743
    40744
    40745
    40746
  22. What is stock fuel pressure for a 1992 2.5 Carb car?

    What is stock fuel pressure suppose to be?

    I want to add external pump, but not sure if I need high pressure or not.

    Thanks

    40692
  23. Replies
    60
    Views
    4,482

    Re: Who's got the fastest bolt-on car?

    Sorry, I know this thread is old, but I thought I would add my 2cents.

    My car was a Stock Block, Stock Pistons (cast) and a Stock Head.

    I was running a stock computer with a grainger valve,...
  24. Replies
    8
    Views
    1,503

    Re: NEW denso alternators, source ?

    You bought a genuine Denso alt for $127? I find that hard to believe.

    The units I sell are not from China, and carry a 2 year warranty
  25. Thread: Weird problem

    by Lugert
    Replies
    25
    Views
    2,519

    Re: Weird problem

    Check for the intermittent block of wood under the skinny pedal on the right.
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4