Thanks for the link! Just read through it and I'm going to give that info a try.
Type: Posts; User: motorhead153; Keyword(s):
Thanks for the link! Just read through it and I'm going to give that info a try.
Yup im fully aware 10.0 is the lowest value it will read. I'm running +20's (52lb) injectors and tune is scaled for 65lb injectors.
I've got a 86 SC with a 89 SMEC setup running a flash-able boost button SMEC I've been picking away at adjusting my tune and have it close to where i want it...except for cold start, as in when it...
Got around to swapping out the master cylinder for the 24mm one today and WOW what a difference! So much better, With the same force I would use before to stop hard is about the same force I would...
Yeah that make sense. Ok so I really need to swap out this MC and get where it needs to be, then see where its at as far as bias then. Thanks!
That could have something to do with it, I had been running 200 treadwear tires that are fairly sticky that I recently took off and no issues with rear lock up also. The only time I've had any lockup...
Huh, I have never had this problem with my setup.
I do have a set of 91+ knuckles that I do plan on using eventually, and I would love to buy that coil over setup one day, the plan is to...
So a bunch of years back I did the full SLH brake upgrade on my Shelby Charger ( Caravan calipers, Daytona rear vented disc, Daytona 4 wheel disc prop valve, and D150 master cylinder. I also replaced...
Looks like rock auto might have manual racks back in stockhttps://uploads.tapatalk-cdn.com/20170715/09c0639b2bfcda24359d60a4660d65cd.jpg
Sent from my SM-G900W8 using Tapatalk
I did development one one years ago but just didn't complete it because of life. Maybe it's time to get back to...
I took a picture of where I think I'm supposed to set the Rev limiter but I'm not understanding the values. In the "table description" it has info but I'm not sure what it means. ...
Protection features? Like what? should I not plug into the car with out it? I was finally able to flash the smec for the the first time! I was ecstatic!! I made changes to the Rev limits to easily...
So I disected the cable from the board and once I got the hot glue off All the wires were still connected to the board. I used a soldering iron to release them and shorted the orange to the yellow...
Ok I'll dissect the one end and see what's up.
Sent from my SM-G900W8 using Tapatalk
I guess I could undue the connections but as you may have noticed I'm not good with electronics lol. So that basically means that this cable has been bad since new and the cause of all my swearing...
Yes the car runs drives and does everything it's supposed to. Is there a way to check the diagnosis port in the car? I took some pictures of the cable I have and I took a picture of the 2 terminals...
Ok $200.00 and a new solid state drive and I'm back in business! So I went through the info again and went through all my settings. I found a discrepancy, on the mptune thread it says to turn off the...
I haven't been able to do anymore with mptune or scan because when I was trying to set up mp scan my labtop slid off the front of the car killing the hard drive in the fall :mad:.
Dropped it off...
Here is the other log,
-Comport analysis for mptune version 2.0.5.9
-Locating ports on computer-
name:USB Serial Port (COM6) deviceid:FTDIBUS\VID_0403+PID_6001+BB1UBXN8A\0000
number of ftdi...
The images should be up now
No I haven't done anything with mp scan I'll give it a try tonight. Tonight I'll also post the other file and try to get the photos I posted to work
Yes I was trying to flash a Cal. I'll see if I can get the photos to show up
Ok so I went through the instructions and checked everything, I think I have the setting right but I'll post the screen shots just in case I missed anything
...
Yes I bought the flashable SMEC and the FTDI cable from Boost Button back in 2012. I have the bootstrap hooked up as per Rob's directions directly to the battery ( I double checked it was in the...
I went through that process and it looks as though everything checks out. I will check it again and take a screen shot and post the pics and let you all see if I'm missing anything. I also have...